On 21/10/2019 05:44, Vinod Koul wrote:
On 11-10-19, 16:44, Srinivas Kandagatla wrote:+static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) +{ + struct qcom_swrm_ctrl *ctrl = dev_id; + u32 sts, value; + unsigned long flags; + + ctrl->reg_read(ctrl, SWRM_INTERRUPT_STATUS, &sts); + + if (sts & SWRM_INTERRUPT_STATUS_CMD_ERROR) { + ctrl->reg_read(ctrl, SWRM_CMD_FIFO_STATUS, &value); + dev_err_ratelimited(ctrl->dev, + "CMD error, fifo status 0x%x\n", + value); + ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CMD, 0x1); + } + + if ((sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED) || + sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) + schedule_work(&ctrl->slave_work);we are in irq thread, so why not do the work here rather than schedule it?
The reason is that, sdw_handle_slave_status() we will read device id registers, which are fifo based in this controller and triggers an interrupt for each read. So all the such reads will timeout waiting for interrupt if we do not do it in a separate thread.
Bandwidth parameters are currently coming from board specific Device Tree, which are programmed here.+static int qcom_swrm_compute_params(struct sdw_bus *bus) +{ + struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus); + struct sdw_master_runtime *m_rt; + struct sdw_slave_runtime *s_rt; + struct sdw_port_runtime *p_rt; + struct qcom_swrm_port_config *pcfg; + int i = 0; + + list_for_each_entry(m_rt, &bus->m_rt_list, bus_node) { + list_for_each_entry(p_rt, &m_rt->port_list, port_node) { + pcfg = &ctrl->pconfig[p_rt->num - 1]; + p_rt->transport_params.port_num = p_rt->num; + p_rt->transport_params.sample_interval = pcfg->si + 1; + p_rt->transport_params.offset1 = pcfg->off1; + p_rt->transport_params.offset2 = pcfg->off2; + } + + list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) { + list_for_each_entry(p_rt, &s_rt->port_list, port_node) { + pcfg = &ctrl->pconfig[i]; + p_rt->transport_params.port_num = p_rt->num; + p_rt->transport_params.sample_interval = + pcfg->si + 1; + p_rt->transport_params.offset1 = pcfg->off1; + p_rt->transport_params.offset2 = pcfg->off2; + i++; + }Can you explain this one, am not sure I understood this. This fn is supposed to compute and fill up the params, all I can see is filling up!
+static const struct snd_soc_dai_ops qcom_swrm_pdm_dai_ops = { + .hw_params = qcom_swrm_hw_params, + .prepare = qcom_swrm_prepare, + .hw_free = qcom_swrm_hw_free, + .startup = qcom_swrm_startup, + .shutdown = qcom_swrm_shutdown, + .set_sdw_stream = qcom_swrm_set_sdw_stream,why does indent look off to me!
Yep, Fixed in next version. --srini
