Hi Marco,
Le 25/10/2019 à 20:45, Marco Felsch a écrit :
Hi Joris,
On 19-10-25 10:22, Joris Offouga wrote:
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Joris Offouga <offougajoris@xxxxxxxxx>
Signed-off-by: Fabio Estevam <festevam@xxxxxxxxx>
Signed-off-by: Otavio Salvador <otavio@xxxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/imx7d-pico.dtsi | 84 +++++++++++++++++++++++++++++++
1 file changed, 84 insertions(+)
diff --git a/arch/arm/boot/dts/imx7d-pico.dtsi b/arch/arm/boot/dts/imx7d-pico.dtsi
index 6f50ebf31a0a..9042b1e6f1db 100644
--- a/arch/arm/boot/dts/imx7d-pico.dtsi
+++ b/arch/arm/boot/dts/imx7d-pico.dtsi
@@ -69,6 +69,37 @@
clocks = <&clks IMX7D_CLKO2_ROOT_DIV>;
clock-names = "ext_clock";
};
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm4 0 50000 0>;
^
If not inverted please drop the this flag.
Also you need to add
&pwm4 {
status = "okay";
};
This node is already provide but i agree with you i move pinctrl in
pwm4 node and rename the muxing
And so you can do the pwm pinctrl within that node, see below.
+ brightness-levels = <0 36 72 108 144 180 216 255>;
+ default-brightness-level = <6>;
+ status = "okay";
status can be dropped too.
+ };
+
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
Missing the muxing?
No this pin is already drive
+ enable-active-high;
+ };
+
+ panel {
+ compatible = "vxt,vl050-8048nt-c01";
+ backlight = <&backlight>;
+ power-supply = <®_lcd_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
Please sort the nodes alphabetical.
okay thanks for your review
otherwise Fabio made me notice that I should leave his From however with
the changes made I should put mine?
Best regards,
Joris
};
&clks {
@@ -230,6 +261,18 @@
};
};
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif>;
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
+
&sai1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai1>;
@@ -349,6 +392,13 @@
};
&iomuxc {
+
+ pinctrl_backlight: backlight {
^
please add 'grp'
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO11__PWM4_OUT 0x0
+ >;
+ };
IMHO the muxing is part of the pwm4 node. So rename it to
'pinctrl_pwm4: pwm4grp'.
Regards,
Marco
+
pinctrl_ecspi3: ecspi3grp {
fsl,pins = <
MX7D_PAD_I2C1_SCL__ECSPI3_MISO 0x2
@@ -413,6 +463,40 @@
>;
};
+ pinctrl_lcdif: lcdifgrp {
+ fsl,pins = <
+ MX7D_PAD_LCD_DATA00__LCD_DATA0 0x79
+ MX7D_PAD_LCD_DATA01__LCD_DATA1 0x79
+ MX7D_PAD_LCD_DATA02__LCD_DATA2 0x79
+ MX7D_PAD_LCD_DATA03__LCD_DATA3 0x79
+ MX7D_PAD_LCD_DATA04__LCD_DATA4 0x79
+ MX7D_PAD_LCD_DATA05__LCD_DATA5 0x79
+ MX7D_PAD_LCD_DATA06__LCD_DATA6 0x79
+ MX7D_PAD_LCD_DATA07__LCD_DATA7 0x79
+ MX7D_PAD_LCD_DATA08__LCD_DATA8 0x79
+ MX7D_PAD_LCD_DATA09__LCD_DATA9 0x79
+ MX7D_PAD_LCD_DATA10__LCD_DATA10 0x79
+ MX7D_PAD_LCD_DATA11__LCD_DATA11 0x79
+ MX7D_PAD_LCD_DATA12__LCD_DATA12 0x79
+ MX7D_PAD_LCD_DATA13__LCD_DATA13 0x79
+ MX7D_PAD_LCD_DATA14__LCD_DATA14 0x79
+ MX7D_PAD_LCD_DATA15__LCD_DATA15 0x79
+ MX7D_PAD_LCD_DATA16__LCD_DATA16 0x79
+ MX7D_PAD_LCD_DATA17__LCD_DATA17 0x79
+ MX7D_PAD_LCD_DATA18__LCD_DATA18 0x79
+ MX7D_PAD_LCD_DATA19__LCD_DATA19 0x79
+ MX7D_PAD_LCD_DATA20__LCD_DATA20 0x79
+ MX7D_PAD_LCD_DATA21__LCD_DATA21 0x79
+ MX7D_PAD_LCD_DATA22__LCD_DATA22 0x79
+ MX7D_PAD_LCD_DATA23__LCD_DATA23 0x79
+ MX7D_PAD_LCD_CLK__LCD_CLK 0x79
+ MX7D_PAD_LCD_ENABLE__LCD_ENABLE 0x78
+ MX7D_PAD_LCD_VSYNC__LCD_VSYNC 0x78
+ MX7D_PAD_LCD_HSYNC__LCD_HSYNC 0x78
+ MX7D_PAD_LCD_RESET__GPIO3_IO4 0x14
+ >;
+ };
+
pinctrl_pwm1: pwm1 {
fsl,pins = <
MX7D_PAD_GPIO1_IO08__PWM1_OUT 0x7f
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
