ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
a real-time clock (RTC), 3 GPO/regulator control pins, HALL input
and a 32.768 kHz clock gate.
Document the dt bindings drivers are using.
Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
---
No changes since v1
.../bindings/mfd/rohm,bd71828-pmic.txt | 180 ++++++++++++++++++
1 file changed, 180 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
new file mode 100644
index 000000000000..125efa9f3de0
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
@@ -0,0 +1,180 @@
+* ROHM BD71828 Power Management Integrated Circuit bindings
+
+BD71828GW is a single-chip power management IC for battery-powered portable
+devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA single-cell
+linear charger. Also included is a Coulomb counter, a real-time clock (RTC),
+and a 32.768 kHz clock gate.
+
+Required properties:
+ - compatible : Should be "rohm,bd71828".
+ - reg : I2C slave address.
+ - interrupt-parent : Phandle to the parent interrupt controller.
+ - interrupts : The interrupt line the device is connected to.
+ - clocks : The parent clock connected to PMIC.
+ - #clock-cells : Should be 0.
+ - regulators : List of child nodes that specify the
+ regulators. Please see
+ ../regulator/rohm,bd71828-regulator.txt
+ - gpio-controller : To indicate BD71828 acts as a GPIO controller.
+ - #gpio-cells : Should be 2. The first cell is the pin number
+ and the second cell is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+
+The BD71828 RUN state is divided into 4 configurable run-levels named RUN0,
+RUN1, RUN2 and RUN3. Bucks 1, 2, 6 and 7 can be either controlled individually
+via I2C, or some/all of them can be bound to run-levels and controlled as a
+group. If bucks are controlled individually these run-levels are ignored. See
+../regulator/rohm,bd71828-regulator.txt for how to define regulator voltages
+for run-levels. Run-levels can be changed by I2C or GPIO depending on PMIC's OTP
+configuration.
+
+Optional properties:
+- clock-output-names : Should contain name for output clock.
+- rohm,dvs-vsel-gpios : GPIOs used to control PMIC run-levels. Should
+ describe two GPIOs. (See run-level control in
+ data-sheet). If this property is omitted but
+ some bucks are marked to be controlled by
+ run-levels - then OTP option allowing
+ run-level control via I2C is assumed.
+- gpio-reserved-ranges : Usage of GPIO pins can be changed via OTP.
+ This property can be used to mark the pins
+ which should not be configured for GPIO.
+ Please see the ../gpio/gpio.txt for more
+ information.
+
+Example:
+
+ /* external oscillator node */
+ osc: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <1>;
+ clock-frequency = <32768>;
+ clock-output-names = "osc";
+ };
+
+ pmic: pmic@4b {
+ compatible = "rohm,bd71828";
+ reg = <0x4b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <29 GPIO_ACTIVE_LOW>;
+ clocks = <&osc 0>;
+ #clock-cells = <0>;
+ clock-output-names = "bd71828-32k-out";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <4>;
+ gpio-reserved-ranges = <0 1 2 1>;
+ gpio-line-names = "EPDEN";
+ rohm,dvs-vsel-gpios = <&gpio1 12 0>,
+ <&gpio1 13 0>;
+ regulators {
+ buck1: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ buck2: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ buck3: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-boot-on;
+ };
+ buck4: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+ buck5: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ buck6: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ buck7: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ ldo1: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo2: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo5: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo6: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+ ldo7_reg: LDO7 {
+ regulator-name = "ldo7";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
