Re: [PATCH 7/7] ARM: sunxi: dt: add PRCM clk and reset controller subdevices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 28/04/2014 18:02, Chen-Yu Tsai wrote:
> Hi,
>
> On Mon, Apr 28, 2014 at 10:58 PM, Boris BREZILLON
> <boris.brezillon@xxxxxxxxxxxxxxxxxx> wrote:
>> Add DT definitions for PRCM (Power/Reset/Clock Management) clock and reset
>> controller subdevices.
>>
>> Signed-off-by: Boris BREZILLON <boris.brezillon@xxxxxxxxxxxxxxxxxx>
>> ---
>>  arch/arm/boot/dts/sun6i-a31.dtsi | 49 ++++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 49 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
>> index ec3253a..83a1634 100644
>> --- a/arch/arm/boot/dts/sun6i-a31.dtsi
>> +++ b/arch/arm/boot/dts/sun6i-a31.dtsi
>> @@ -501,6 +501,55 @@
>>                 prcm@01f01c00 {
> Seems the address here was wrong to start with.

Absolutely, I'll fix it.

>
>>                         compatible = "allwinner,sun6i-a31-prcm";
>>                         reg = <0x01f01400 0x200>;
>> +
>> +                       ar100_mux: ar100_mux {
> Might we use clk@01f01XXX for the names of the clock nodes?

Actually, I had a discussion with Maxime, and we decided to remove the
address suffix because the PRCM block is not a bus, and thus should not
have child node with addresses.
But I'm not a DT binding expert (it might be acceptable to define child
nodes with addresses even when the parent is not a bus :-)).
Advices from DT maintainers on that specific point would be great.

Best Regards,

Boris

>> +                               compatible = "allwinner,sun6i-a31-ar100-mux-clk";
>> +                               #clock-cells = <0>;
>> +                               clocks = <&osc32k>, <&osc24M>, <&pll6>, <&pll6>;
>> +                       };
>> +
>> +                       ar100: ar100 {
>> +                               compatible = "allwinner,sun6i-a31-ar100-clk";
>> +                               #clock-cells = <0>;
>> +                               clocks = <&ar100_mux>;
>> +                       };
>> +
>> +                       ar100_div: ar100_div {
>> +                               compatible = "allwinner,sun6i-a31-ar100-div-clk";
>> +                               #clock-cells = <0>;
>> +                               clocks = <&ar100>;
>> +                       };
>> +
>> +                       ahb0: ahb0 {
>> +                               compatible = "fixed-factor-clock";
>> +                               #clock-cells = <0>;
>> +                               clock-div = <1>;
>> +                               clock-mult = <1>;
>> +                               clocks = <&ar100_div>;
>> +                               clock-output-names = "ahb0";
>> +                       };
>> +
>> +                       apb0: apb0 {
>> +                               compatible = "allwinner,sun6i-a31-apb0-clk";
>> +                               #clock-cells = <0>;
>> +                               clocks = <&ahb0>;
>> +                               clock-output-names = "apb0";
>> +                       };
>> +
>> +                       apb0_gates: apb0_gates {
>> +                               compatible = "allwinner,sun6i-a31-apb0-gates-clk";
>> +                               #clock-cells = <1>;
>> +                               clocks = <&apb0>;
>> +                               clock-output-names = "apb0_pio", "apb0_ir",
>> +                                               "apb0_timer01", "apb0_p2wi",
>> +                                               "apb0_uart", "apb0_1wire",
>> +                                               "apb0_i2c";
>> +                       };
>> +
>> +                       apb0_rst: apb0_rst {
> Also use reset@01f01XXX here?
>
>> +                               compatible = "allwinner,sun6i-a31-clock-reset";
>> +                               #reset-cells = <1>;
>> +                       };
>>                 };
>>         };
>>  };
> Thanks!
>
> ChenYu

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux