There are several boards available depending on the PCB
(3 antennas support and several revison). Add a dtsi file to share
common binding between all kizbox2 boards. This patch also add support
for the kizbox2-2 variant.
Signed-off-by: Kévin RAYMOND <k.raymond@xxxxxxxxxxx>
Signed-off-by: Mickael GARDET <m.gardet@xxxxxxxxxxx>
Signed-off-by: Kamel Bouhara <kamel.bouhara@xxxxxxxxxxx>
---
Changes in v2:
- Replaced "_" by "-" in dts/dtsi file names
- Fixed unusual C++ Style comments
arch/arm/boot/dts/Makefile | 2 +-
arch/arm/boot/dts/at91-kizbox.dts | 173 +++++++-------
arch/arm/boot/dts/at91-kizbox2-2.dts | 26 +++
arch/arm/boot/dts/at91-kizbox2-common.dtsi | 258 +++++++++++++++++++++
arch/arm/boot/dts/at91-kizbox2.dts | 244 -------------------
5 files changed, 370 insertions(+), 333 deletions(-)
create mode 100644 arch/arm/boot/dts/at91-kizbox2-2.dts
create mode 100644 arch/arm/boot/dts/at91-kizbox2-common.dtsi
delete mode 100644 arch/arm/boot/dts/at91-kizbox2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3bda216c41be..4ac053115a8e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -45,7 +45,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91sam9x25ek.dtb \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
- at91-kizbox2.dtb \
+ at91-kizbox2-2.dtb \
at91-kizbox3-hs.dtb \
at91-nattis-2-natte-2.dtb \
at91-sama5d27_som1_ek.dtb \
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 90996eaf73b2..9eb1ea750159 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -28,85 +28,6 @@
};
};
- ahb {
- apb {
- tcb0: timer@fffa0000 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>, <1>;
- };
-
- timer@2 {
- compatible = "atmel,tcb-timer";
- reg = <2>;
- };
- };
-
- macb0: ethernet@fffc4000 {
- phy-mode = "mii";
- pinctrl-0 = <&pinctrl_macb_rmii
- &pinctrl_macb_rmii_mii_alt>;
- status = "okay";
- };
-
- usart3: serial@fffd0000 {
- status = "okay";
- };
-
- dbgu: serial@fffff200 {
- status = "okay";
- };
-
- watchdog@fffffd40 {
- timeout-sec = <15>;
- atmel,max-heartbeat-sec = <16>;
- atmel,min-heartbeat-sec = <0>;
- status = "okay";
- };
- };
-
- usb0: ohci@500000 {
- num-ports = <1>;
- status = "okay";
- };
-
- ebi: ebi@10000000 {
- status = "okay";
-
- nand_controller: nand-controller {
- status = "okay";
- pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
- pinctrl-names = "default";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "soft";
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
@@ -127,15 +48,6 @@
};
};
- i2c-gpio-0 {
- status = "okay";
-
- rtc: pcf8563@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
-
pwm_leds {
compatible = "pwm-leds";
@@ -179,3 +91,88 @@
&pinctrl_tcb1_tiob0>;
};
};
+
+&tcb0 {
+ timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>, <1>;
+ };
+
+ timer@2 {
+ compatible = "atmel,tcb-timer";
+ reg = <2>;
+ };
+};
+
+&ebi {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
+&macb0 {
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_macb_rmii
+ &pinctrl_macb_rmii_mii_alt>;
+ status = "okay";
+};
+
+&usart3 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+&watchdog {
+ timeout-sec = <15>;
+ atmel,max-heartbeat-sec = <16>;
+ atmel,min-heartbeat-sec = <0>;
+ status = "okay";
+};
+
+&usb0 {
+ num-ports = <1>;
+ status = "okay";
+};
+
+&i2c-gpio-0 {
+ status = "okay";
+
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
diff --git a/arch/arm/boot/dts/at91-kizbox2-2.dts b/arch/arm/boot/dts/at91-kizbox2-2.dts
new file mode 100644
index 000000000000..cab8b3579efa
--- /dev/null
+++ b/arch/arm/boot/dts/at91-kizbox2-2.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-kizbox2-2.dts - Device Tree file for the Kizbox2 with
+ * two head board
+ *
+ * Copyright (C) 2015 Overkiz SAS
+ *
+ * Authors: Antoine Aubert <a.aubert@xxxxxxxxxxx>
+ * Kévin Raymond <k.raymond@xxxxxxxxxxx>
+ */
+/dts-v1/;
+#include "at91-kizbox2-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox 2 with two heads";
+ compatible = "overkiz,kizbox2-2", "atmel,sama5d31",
+ "atmel,sama5d3", "atmel,sama5";
+};
+
+&usart1 {
+ status = "okay";
+};
+
+&usart2 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-kizbox2-common.dtsi b/arch/arm/boot/dts/at91-kizbox2-common.dtsi
new file mode 100644
index 000000000000..af38253a6e7a
--- /dev/null
+++ b/arch/arm/boot/dts/at91-kizbox2-common.dtsi
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-kizbox2_common.dtsi - Device Tree Include file for
+ * Overkiz Kizbox 2 family SoC
+ *
+ * Copyright (C) 2014-2018 Overkiz SAS
+ *
+ * Authors: Antoine Aubert <a.aubert@xxxxxxxxxxx>
+ * Gaël Portay <g.portay@xxxxxxxxxxx>
+ * Kévin Raymond <k.raymond@xxxxxxxxxxx>
+ */
+#include "sama5d31.dtsi"
+
+/ {
+ chosen {
+ bootargs = "ubi.mtd=ubi";
+ stdout-path = &dbgu;
+ };
+
+ memory {
+ reg = <0x20000000 0x10000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ prog {
+ label = "PB_PROG";
+ gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
+ linux,code = <0x102>;
+ wakeup-source;
+ };
+
+ reset {
+ label = "PB_RST";
+ gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+ linux,code = <0x100>;
+ wakeup-source;
+ };
+
+ user {
+ label = "PB_USER";
+ gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x101>;
+ wakeup-source;
+ };
+ };
+
+ pwm_leds {
+ compatible = "pwm-leds";
+
+ blue {
+ label = "pwm:blue:user";
+ pwms = <&pwm0 2 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "none";
+ };
+
+ green {
+ label = "pwm:green:user";
+ pwms = <&pwm0 1 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+
+ red {
+ label = "pwm:red:user";
+ pwms = <&pwm0 0 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ pmic: act8865@5b {
+ compatible = "active-semi,act8865";
+ reg = <0x5b>;
+ status = "okay";
+
+ regulators {
+ vcc_1v8_reg: DCDC_REG1 {
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc_1v2_reg: DCDC_REG2 {
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vcc_3v3_reg: DCDC_REG3 {
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddfuse_reg: LDO_REG1 {
+ regulator-name = "FUSE_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vddana_reg: LDO_REG2 {
+ regulator-name = "VDDANA";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vled_reg: LDO_REG3 {
+ regulator-name = "VLED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ v3v8_rf_reg: LDO_REG4 {
+ regulator-name = "V3V8_RF";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&usart0 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "disabled";
+};
+
+&usart1 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "disabled";
+};
+
+&usart2 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "disabled";
+};
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_pwmh0_1
+ &pinctrl_pwm0_pwmh1_1
+ &pinctrl_pwm0_pwmh2_0>;
+ status = "okay";
+};
+
+&adc0 {
+ atmel,adc-vref = <3333>;
+ status = "okay";
+};
+
+&macb1 {
+ phy-mode = "rmii";
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&ebi {
+ pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand@3 {
+ reg = <0x3 0x0 0x2>;
+ atmel,rb = <0>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+/* WMBUS (inverted with IO in the latest schematic) */
+&pinctrl_usart0 {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+};
+
+/* RTS */
+&pinctrl_usart1 {
+ atmel,pins =
+ <AT91_PIOB 28 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOE 7 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+};
+
+/* IO (inverted with WMBUS in the latest schematic) */
+&pinctrl_usart2 {
+ atmel,pins =
+ <AT91_PIOE 25 AT91_PERIPH_B AT91_PINCTRL_NONE
+ AT91_PIOE 26 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
+ AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+};
diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
deleted file mode 100644
index 86d821884bd4..000000000000
--- a/arch/arm/boot/dts/at91-kizbox2.dts
+++ /dev/null
@@ -1,244 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * at91-kizbox2.dts - Device Tree file for Overkiz Kizbox 2 board
- *
- * Copyright (C) 2014 Gaël PORTAY <g.portay@xxxxxxxxxxx>
- */
-/dts-v1/;
-#include "sama5d31.dtsi"
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- model = "Overkiz Kizbox 2";
- compatible = "overkiz,kizbox2", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
-
- chosen {
- bootargs = "ubi.mtd=ubi";
- stdout-path = &dbgu;
- };
-
- memory {
- reg = <0x20000000 0x10000000>;
- };
-
- clocks {
- slow_xtal {
- clock-frequency = <32768>;
- };
-
- main_xtal {
- clock-frequency = <12000000>;
- };
- };
-
- ahb {
- apb {
- i2c1: i2c@f0018000 {
- status = "okay";
-
- pmic: act8865@5b {
- compatible = "active-semi,act8865";
- reg = <0x5b>;
- status = "okay";
-
- regulators {
- vcc_1v8_reg: DCDC_REG1 {
- regulator-name = "VCC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- vcc_1v2_reg: DCDC_REG2 {
- regulator-name = "VCC_1V2";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- vcc_3v3_reg: DCDC_REG3 {
- regulator-name = "VCC_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vddfuse_reg: LDO_REG1 {
- regulator-name = "FUSE_2V5";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- };
-
- vddana_reg: LDO_REG2 {
- regulator-name = "VDDANA";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vled_reg: LDO_REG3 {
- regulator-name = "VLED";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- v3v8_rf_reg: LDO_REG4 {
- regulator-name = "V3V8_RF";
- regulator-min-microvolt = <3800000>;
- regulator-max-microvolt = <3800000>;
- regulator-always-on;
- };
- };
- };
- };
-
- tcb0: timer@f0010000 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>;
- };
-
- timer@1 {
- compatible = "atmel,tcb-timer";
- reg = <1>;
- };
- };
-
- usart0: serial@f001c000 {
- status = "okay";
- };
-
- usart1: serial@f0020000 {
- status = "okay";
- };
-
- pwm0: pwm@f002c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm0_pwmh0_1
- &pinctrl_pwm0_pwmh1_1
- &pinctrl_pwm0_pwmh2_0>;
- status = "okay";
- };
-
- adc0: adc@f8018000 {
- atmel,adc-vref = <3333>;
- status = "okay";
- };
-
- usart2: serial@f8020000 {
- status = "okay";
- };
-
- macb1: ethernet@f802c000 {
- phy-mode = "rmii";
- status = "okay";
- };
-
- dbgu: serial@ffffee00 {
- status = "okay";
- };
-
- watchdog@fffffe40 {
- status = "okay";
- };
- };
-
- usb1: ohci@600000 {
- status = "okay";
- };
-
- usb2: ehci@700000 {
- status = "okay";
- };
-
- ebi: ebi@10000000 {
- pinctrl-0 = <&pinctrl_ebi_nand_addr>;
- pinctrl-names = "default";
- status = "okay";
-
- nand_controller: nand-controller {
- status = "okay";
-
- nand@3 {
- reg = <0x3 0x0 0x2>;
- atmel,rb = <0>;
- nand-bus-width = <8>;
- nand-ecc-mode = "hw";
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
- };
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
-
- prog {
- label = "PB_PROG";
- gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
- linux,code = <0x102>;
- wakeup-source;
- };
-
- reset {
- label = "PB_RST";
- gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
- linux,code = <0x100>;
- wakeup-source;
- };
-
- user {
- label = "PB_USER";
- gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
- linux,code = <0x101>;
- wakeup-source;
- };
- };
-
- pwm_leds {
- compatible = "pwm-leds";
-
- blue {
- label = "pwm:blue:user";
- pwms = <&pwm0 2 10000000 0>;
- max-brightness = <255>;
- linux,default-trigger = "default-on";
- };
-
- green {
- label = "pwm:green:user";
- pwms = <&pwm0 1 10000000 0>;
- max-brightness = <255>;
- linux,default-trigger = "default-on";
- };
-
- red {
- label = "pwm:red:user";
- pwms = <&pwm0 0 10000000 0>;
- max-brightness = <255>;
- linux,default-trigger = "default-on";
- };
- };
-};
--
2.23.0
