hi Ulf
Le 10/4/19 à 9:31 AM, Ulf Hansson a écrit :
On Thu, 5 Sep 2019 at 14:22, Ludovic Barre <ludovic.Barre@xxxxxx> wrote:
From: Ludovic Barre <ludovic.barre@xxxxxx>
This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion monitors step by step the busy progression
start/in-progress/end. On sdmmc variant, the monitoring of busy steps
is difficult and not adapted (the software can miss a step and locks
the monitoring), the sdmmc has just need to wait the busyd0end bit
without monitoring all the changes.
To me it's a bit of the opposite as you describe it above. The legacy
variants suffers from a somewhat broken HW that generates also a
"busystart" IRQ. For the stm32_sdmmc variant, it's more clean/correct
as only a busyend IRQ is raised.
Maybe you can rephrase the above a bit to make that more clear somehow.
Yes, I will rephrase.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end status.
Signed-off-by: Ludovic Barre <ludovic.barre@xxxxxx>
---
drivers/mmc/host/mmci.c | 3 +++
drivers/mmc/host/mmci.h | 1 +
drivers/mmc/host/mmci_stm32_sdmmc.c | 38 +++++++++++++++++++++++++++++
3 files changed, 42 insertions(+)
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index e20164f4354d..a666d826dbbd 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -260,6 +260,9 @@ static struct variant_data variant_stm32_sdmmc = {
.datalength_bits = 25,
.datactrl_blocksz = 14,
.stm32_idmabsize_mask = GENMASK(12, 5),
+ .busy_timeout = true,
+ .busy_detect_flag = MCI_STM32_BUSYD0,
+ .busy_detect_mask = MCI_STM32_BUSYD0ENDMASK,
.init = sdmmc_variant_init,
};
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 733f9a035b06..841c5281beb5 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -164,6 +164,7 @@
#define MCI_ST_CARDBUSY (1 << 24)
/* Extended status bits for the STM32 variants */
#define MCI_STM32_BUSYD0 BIT(20)
+#define MCI_STM32_BUSYD0END BIT(21)
#define MMCICLEAR 0x038
#define MCI_CMDCRCFAILCLR (1 << 0)
diff --git a/drivers/mmc/host/mmci_stm32_sdmmc.c b/drivers/mmc/host/mmci_stm32_sdmmc.c
index 8e83ae6920ae..bb5499cc9e81 100644
--- a/drivers/mmc/host/mmci_stm32_sdmmc.c
+++ b/drivers/mmc/host/mmci_stm32_sdmmc.c
@@ -282,6 +282,43 @@ static u32 sdmmc_get_dctrl_cfg(struct mmci_host *host)
return datactrl;
}
+bool sdmmc_busy_complete(struct mmci_host *host, u32 status, u32 err_msk)
+{
+ void __iomem *base = host->base;
+ u32 busy_d0, busy_d0end, mask;
+
+ mask = readl_relaxed(base + MMCIMASK0);
+ busy_d0end = readl_relaxed(base + MMCISTATUS) & MCI_STM32_BUSYD0END;
+ busy_d0 = readl_relaxed(base + MMCISTATUS) & MCI_STM32_BUSYD0;
I have found some potential optimizations, but I leave it to you to
decide what to do with my comments.
*) You could avoid to read registers upfront, if that be skipped
because of checking a known error condition. For example:
"if (!host->busy_status && !(status & err_msk))" - would tell if it's
even worth considering to unmask the busyend IRQ.
Yes, it's a possibility, but I prefer to keep reading the bits
busy_doend and busy_d0. This is not the most optimized way, but it is
easier to understand the completion's reason (based on hardware bit).
On the other hand, I would be independent of any change about status or
busy_status.
**) Reading MMCISTATUS twice in row seems a bit silly, why not read it
once and store its value in a local variable that you operate upon
instead.
yes, I will store MMCISTATUS in local variable (thx).
+
+ /* complete if there is an error or busy_d0end */
+ if ((status & err_msk) || busy_d0end)
+ goto complete;
From here, you may end up writing to MMCIMASK0 and MMCICLEAR, even if
you didn't unmask the busyend IRQ in first place.
I will add this condition into
complete:
if (host->busy_status) {
...
}
return true;
}
+
+ /*
+ * On response the busy signaling is reflected in the BUSYD0 flag.
+ * if busy_d0 is in-progress we must activate busyd0end interrupt
+ * to wait this completion. Else this request has no busy step.
+ */
+ if (busy_d0) {
+ if (!host->busy_status) {
+ writel_relaxed(mask | host->variant->busy_detect_mask,
+ base + MMCIMASK0);
+ host->busy_status = status &
+ (MCI_CMDSENT | MCI_CMDRESPEND);
+ }
+ return false;
+ }
+
+complete:
+ writel_relaxed(mask & ~host->variant->busy_detect_mask,
+ base + MMCIMASK0);
+ writel_relaxed(host->variant->busy_detect_mask, base + MMCICLEAR);
+ host->busy_status = 0;
+
+ return true;
+}
+
static struct mmci_host_ops sdmmc_variant_ops = {
.validate_data = sdmmc_idma_validate_data,
.prep_data = sdmmc_idma_prep_data,
@@ -292,6 +329,7 @@ static struct mmci_host_ops sdmmc_variant_ops = {
.dma_finalize = sdmmc_idma_finalize,
.set_clkreg = mmci_sdmmc_set_clkreg,
.set_pwrreg = mmci_sdmmc_set_pwrreg,
+ .busy_complete = sdmmc_busy_complete,
};
void sdmmc_variant_init(struct mmci_host *host)
--
2.17.1
Other than the comments above, which are plain suggestions for
optimizations, the code looks correct to me!
I will send a next series soon, thx for review.
Kind regards
Uffe
