On Tue, 2019-10-01 at 13:56 +0000, René van Dorst wrote:
> Hi MarkLee,
>
> Quoting MarkLee <Mark-MC.Lee@xxxxxxxxxxxx>:
>
> > * Removes mediatek,physpeed property from dtsi that is useless in PHYLINK
> > * Set gmac0 to fixed-link sgmii 2.5Gbit mode
> > * Set gmac1 to gmii mode that connect to a internal gphy
> >
> > Signed-off-by: MarkLee <Mark-MC.Lee@xxxxxxxxxxxx>
> > ---
> > arch/arm/boot/dts/mt7629-rfb.dts | 13 ++++++++++++-
> > arch/arm/boot/dts/mt7629.dtsi | 2 --
> > 2 files changed, 12 insertions(+), 3 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/mt7629-rfb.dts
> > b/arch/arm/boot/dts/mt7629-rfb.dts
> > index 3621b7d2b22a..6bf1f7d8ddb5 100644
> > --- a/arch/arm/boot/dts/mt7629-rfb.dts
> > +++ b/arch/arm/boot/dts/mt7629-rfb.dts
> > @@ -66,9 +66,21 @@
> > pinctrl-1 = <&ephy_leds_pins>;
> > status = "okay";
> >
> > + gmac0: mac@0 {
> > + compatible = "mediatek,eth-mac";
> > + reg = <0>;
> > + phy-mode = "sgmii";
> > + fixed-link {
> > + speed = <2500>;
> > + full-duplex;
> > + pause;
> > + };
> > + };
> > +
> > gmac1: mac@1 {
> > compatible = "mediatek,eth-mac";
> > reg = <1>;
> > + phy-mode = "gmii";
> > phy-handle = <&phy0>;
> > };
> >
> > @@ -78,7 +90,6 @@
> >
> > phy0: ethernet-phy@0 {
> > reg = <0>;
> > - phy-mode = "gmii";
> > };
> > };
> > };
> > diff --git a/arch/arm/boot/dts/mt7629.dtsi b/arch/arm/boot/dts/mt7629.dtsi
> > index 9608bc2ccb3f..867b88103b9d 100644
> > --- a/arch/arm/boot/dts/mt7629.dtsi
> > +++ b/arch/arm/boot/dts/mt7629.dtsi
> > @@ -468,14 +468,12 @@
> > compatible = "mediatek,mt7629-sgmiisys", "syscon";
> > reg = <0x1b128000 0x3000>;
> > #clock-cells = <1>;
> > - mediatek,physpeed = "2500";
> > };
> >
> > sgmiisys1: syscon@1b130000 {
> > compatible = "mediatek,mt7629-sgmiisys", "syscon";
> > reg = <0x1b130000 0x3000>;
> > #clock-cells = <1>;
> > - mediatek,physpeed = "2500";
> > };
> > };
> > };
> > --
> > 2.17.1
>
> Does MT7629 soc has the same SGMII IP block as on the MT7622?
> If that is the case then phy-mode should set to "2500base-x".
Yes,MT7629 and MT7622 use the same SGMII block.
Thanks for your suggestion, will change gmac0 phy-mode to "2500base-x"
in the next patch.
Mark
> See discussion about the MT7622 [1] and dts of
> mt7622-bananapi-bpi-r64.dts[2][3]
>
> Note the code only set the phy in overclock mode if phymode =
> 2500base-x and the
> link is a fixed-link, see [4].
> Alsp the current code doesn't support sgmii so well. Sgmii at 2.5Gbit is not
> supported at all.
>
> Greats,
>
> René
>
> [1]:
> https://lore.kernel.org/netdev/20190822144433.GT13294@xxxxxxxxxxxxxxxxxxxxx/
> [2]:
> https://lore.kernel.org/netdev/20190825174341.20750-4-opensource@xxxxxxxxxx/
> [3]:
> https://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git/tree/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts#n122
> [4]:
> https://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git/tree/drivers/net/ethernet/mediatek/mtk_sgmii.c#n72
>
>
>
>
>
