On Sun, Sep 15, 2019 at 03:56:52PM +0200, Andrew Lunn wrote:
> > Tinywrkb confirmed to me in private communication that revert of
> > 5502b218e001 fixes Ethernet for him on effected system.
> >
> > He also referred me to an old Cubox-i spec that lists 10/100 Ethernet
> > only for i.MX6 Solo/DualLite variants of Cubox-i. It turns out that
> > there was a plan to use a different 10/100 PHY for Solo/DualLite
> > SOMs. This plan never materialized. All SolidRun i.MX6 SOMs use the same
> > AR8035 PHY that supports 1Gb.
> >
> > Commit 5502b218e001 might be triggering a hardware issue on the affected
> > Cubox-i. I could not reproduce the issue here with Cubox-i and a Dual
> > SOM variant running v5.3-rc8. I have no Solo/DualLite variant handy at
> > the moment.
>
> Could somebody with an affected device show us the output of ethtool
> with and without 5502b218e001. Does one show 1G has been negotiated,
> and the other 100Mbps? If this is true, how does it get 100Mbps
> without that patch? We are missing a piece of the puzzle.
>
> Andrew
linux-test-5.1rc1-a2703de70942-without_bad_commit
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: yes
journalctl -b | egrep -i 'phy|eth|fec'|grep -v usb
kernel: Booting Linux on physical CPU 0x0
kernel: libphy: Fixed MDIO Bus: probed
kernel: libphy: fec_enet_mii_bus: probed
kernel: fec 2188000.ethernet eth0: registered PHC device 0
kernel: dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.31a with HDCP (DWC HDMI 3D TX PHY)
kernel: Generic PHY 2188000.ethernet-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
kernel: fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
systemd-networkd[243]: eth0: Gained carrier
systemd-networkd[243]: eth0: DHCPv4 address 192.168.15.101/24 via 192.168.15.1
systemd-networkd[243]: eth0: Gained IPv6LL
systemd-networkd[243]: eth0: Configured
######################################################################
linux-test-5.1rc1-5502b218e001-with_bad_commit
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: yes
journalctl -b | egrep -i 'phy|eth|fec'|grep -v usb
kernel: Booting Linux on physical CPU 0x0
kernel: libphy: Fixed MDIO Bus: probed
kernel: libphy: fec_enet_mii_bus: probed
kernel: fec 2188000.ethernet eth0: registered PHC device 0
kernel: dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.31a with HDCP (DWC HDMI 3D TX PHY)
kernel: Generic PHY 2188000.ethernet-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
kernel: fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
systemd-networkd[239]: eth0: Gained carrier
systemd-networkd[239]: eth0: Gained IPv6LL
