From: Faiz Abbas <faiz_abbas@xxxxxx>
[ Upstream commit fb59ee37cfe20d10d19568899d1458a58361246c ]
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@xxxxxx>
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
arch/arm/boot/dts/am571x-idk.dts | 7 +------
arch/arm/boot/dts/am572x-idk.dts | 7 +------
arch/arm/boot/dts/am574x-idk.dts | 7 +------
arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 1 +
arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts | 7 +------
arch/arm/boot/dts/am57xx-beagle-x15-revc.dts | 7 +------
6 files changed, 6 insertions(+), 30 deletions(-)
diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index 1d5e99964bbf8..0aaacea1d887b 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -175,14 +175,9 @@
};
&mmc1 {
- pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-names = "default", "hs";
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
pinctrl-1 = <&mmc1_pins_hs>;
- pinctrl-2 = <&mmc1_pins_sdr12>;
- pinctrl-3 = <&mmc1_pins_sdr25>;
- pinctrl-4 = <&mmc1_pins_sdr50>;
- pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
- pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index c65d7f6d3b5a6..ea1c119feaa57 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -16,14 +16,9 @@
};
&mmc1 {
- pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-names = "default", "hs";
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
pinctrl-1 = <&mmc1_pins_hs>;
- pinctrl-2 = <&mmc1_pins_sdr12>;
- pinctrl-3 = <&mmc1_pins_sdr25>;
- pinctrl-4 = <&mmc1_pins_sdr50>;
- pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
- pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts
index dc5141c35610e..7935d70874ce2 100644
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/am574x-idk.dts
@@ -24,14 +24,9 @@
};
&mmc1 {
- pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-names = "default", "hs";
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
pinctrl-1 = <&mmc1_pins_hs>;
- pinctrl-2 = <&mmc1_pins_default>;
- pinctrl-3 = <&mmc1_pins_hs>;
- pinctrl-4 = <&mmc1_pins_sdr50>;
- pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_conf>;
- pinctrl-6 = <&mmc1_pins_ddr50 &mmc1_iodelay_sdr104_conf>;
};
&mmc2 {
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index d02f5fa61e5f5..d50de7a6ea6c5 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -430,6 +430,7 @@
bus-width = <4>;
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+ no-1-8-v;
};
&mmc2 {
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
index a374b5cd6db0e..7b113b52c3fb6 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
@@ -16,14 +16,9 @@
};
&mmc1 {
- pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-names = "default", "hs";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
- pinctrl-2 = <&mmc1_pins_sdr12>;
- pinctrl-3 = <&mmc1_pins_sdr25>;
- pinctrl-4 = <&mmc1_pins_sdr50>;
- pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
- pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
vmmc-supply = <&vdd_3v3>;
vqmmc-supply = <&ldo1_reg>;
};
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts
index 4badd2144db9a..30c500b15b219 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts
@@ -16,14 +16,9 @@
};
&mmc1 {
- pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-names = "default", "hs";
pinctrl-0 = <&mmc1_pins_default>;
pinctrl-1 = <&mmc1_pins_hs>;
- pinctrl-2 = <&mmc1_pins_sdr12>;
- pinctrl-3 = <&mmc1_pins_sdr25>;
- pinctrl-4 = <&mmc1_pins_sdr50>;
- pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
- pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
vmmc-supply = <&vdd_3v3>;
vqmmc-supply = <&ldo1_reg>;
};
--
2.20.1
