> From: Shawn Guo <shawnguo@xxxxxxxxxx>
> Sent: Sunday, August 25, 2019 3:20 AM
> Subject: Re: [PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to
> parse clocks from device tree
>
> On Tue, Aug 20, 2019 at 07:13:15AM -0400, Dong Aisheng wrote:
> > There's a few limitations on the original one cell clock binding
> > (#clock-cells = <1>) that we have to define some SW clock IDs for
> > device tree to reference. This may cause troubles if we want to use
> > common clock IDs for multi platforms support when the clock of those
> > platforms are mostly the same.
> > e.g. Current clock IDs name are defined with SS prefix.
> >
> > However the device may reside in different SS across CPUs, that means
> > the SS prefix may not valid anymore for a new SoC. Furthermore, the
> > device availability of those clocks may also vary a bit.
> >
> > For such situation, we want to eliminate the using of SW Clock IDs and
> > change to use a more close to HW one instead.
> > For SCU clocks usage, only two params required: Resource id + Clock Type.
> > Both parameters are platform independent. So we could use two cells
> > binding to pass those parameters,
> >
> > Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> > Cc: Stephen Boyd <sboyd@xxxxxxxxxx>
> > Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
> > Cc: Sascha Hauer <kernel@xxxxxxxxxxxxxx>
> > Cc: Michael Turquette <mturquette@xxxxxxxxxxxx>
> > Cc: devicetree@xxxxxxxxxxxxxxx
> > Signed-off-by: Dong Aisheng <aisheng.dong@xxxxxxx>
>
> I'm fine with it.
>
> Acked-by: Shawn Guo <shawnguo@xxxxxxxxxx>
>
And this one.
Stephen & Rob,
Do you have change to look at it?
We need this to be finalized early for the following work.
Regards
Aisheng
> Shawn
>
> > ---
> > ChangeLog:
> > v3->v4:
> > * add some comments for various clock types
> > v2->v3:
> > * Changed to two cells binding and register all clocks in driver
> > instead of parse from device tree.
> > v1->v2:
> > * changed to one cell binding inspired by arm,scpi.txt
> > Documentation/devicetree/bindings/arm/arm,scpi.txt
> > Resource ID is encoded in 'reg' property.
> > Clock type is encoded in generic clock-indices property.
> > Then we don't have to search all the DT nodes to fetch
> > those two value to construct clocks which is relatively
> > low efficiency.
> > * Add required power-domain property as well.
> > ---
> > .../devicetree/bindings/arm/freescale/fsl,scu.txt | 12 ++++++-----
> > include/dt-bindings/firmware/imx/rsrc.h | 23
> ++++++++++++++++++++++
> > 2 files changed, 30 insertions(+), 5 deletions(-)
> >
> > diff --git
> > a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > index a575e42..8cee5bf 100644
> > --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > @@ -89,7 +89,10 @@ Required properties:
> > "fsl,imx8qm-clock"
> > "fsl,imx8qxp-clock"
> > followed by "fsl,scu-clk"
> > -- #clock-cells: Should be 1. Contains the Clock ID value.
> > +- #clock-cells: Should be either
> > + 2: Contains the Resource and Clock ID value.
> > + or
> > + 1: Contains the Clock ID value. (DEPRECATED)
> > - clocks: List of clock specifiers, must contain an entry for
> > each required entry in clock-names
> > - clock-names: Should include entries "xtal_32KHz", "xtal_24MHz"
> > @@ -184,7 +187,7 @@ firmware {
> >
> > clk: clk {
> > compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
> > - #clock-cells = <1>;
> > + #clock-cells = <2>;
> > };
> >
> > iomuxc {
> > @@ -229,8 +232,7 @@ serial@5a060000 {
> > ...
> > pinctrl-names = "default";
> > pinctrl-0 = <&pinctrl_lpuart0>;
> > - clocks = <&clk IMX8QXP_UART0_CLK>,
> > - <&clk IMX8QXP_UART0_IPG_CLK>;
> > - clock-names = "per", "ipg";
> > + clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>;
> > + clock-names = "ipg";
> > power-domains = <&pd IMX_SC_R_UART_0>; }; diff --git
> > a/include/dt-bindings/firmware/imx/rsrc.h
> > b/include/dt-bindings/firmware/imx/rsrc.h
> > index 4e61f64..24c153d 100644
> > --- a/include/dt-bindings/firmware/imx/rsrc.h
> > +++ b/include/dt-bindings/firmware/imx/rsrc.h
> > @@ -547,4 +547,27 @@
> > #define IMX_SC_R_ATTESTATION 545
> > #define IMX_SC_R_LAST 546
> >
> > +/*
> > + * Defines for SC PM CLK
> > + */
> > +
> > +/* Normal device resource clock */
> > +#define IMX_SC_PM_CLK_SLV_BUS 0 /* Slave bus clock */
> > +#define IMX_SC_PM_CLK_MST_BUS 1 /* Master bus clock */
> > +#define IMX_SC_PM_CLK_PER 2 /* Peripheral clock */
> > +#define IMX_SC_PM_CLK_PHY 3 /* Phy clock */
> > +#define IMX_SC_PM_CLK_MISC 4 /* Misc clock */
> > +
> > +/* Special clock types which do not belong to above normal clock types */
> > +#define IMX_SC_PM_CLK_MISC0 0 /* Misc 0 clock */
> > +#define IMX_SC_PM_CLK_MISC1 1 /* Misc 1 clock */
> > +#define IMX_SC_PM_CLK_MISC2 2 /* Misc 2 clock */
> > +#define IMX_SC_PM_CLK_MISC3 3 /* Misc 3 clock */
> > +#define IMX_SC_PM_CLK_MISC4 4 /* Misc 4 clock */
> > +
> > +/* Special clock types for CPU/PLL/BYPASS only */
> > +#define IMX_SC_PM_CLK_CPU 2 /* CPU clock */
> > +#define IMX_SC_PM_CLK_PLL 4 /* PLL */
> > +#define IMX_SC_PM_CLK_BYPASS 4 /* Bypass clock */
> > +
> > #endif /* __DT_BINDINGS_RSCRC_IMX_H */
> > --
> > 2.7.4
> >
