PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b
with pon, adc, and gpio nodes
Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++++++++++++++++++++++++
1 file changed, 84 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
new file mode 100644
index 000000000000..dfb71fb8c90a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+// Copyright (c) 2019, Linaro Limited
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmic@2 {
+ compatible = "qcom,pm8150b", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ status = "disabled";
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+
+ chg-temp@9 {
+ reg = <ADC5_CHG_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "chg_temp";
+ };
+ };
+
+ pm8150b_gpios: gpio@c000 {
+ compatible = "qcom,pm8150b-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>,
+ <0x2 0xc1 0 IRQ_TYPE_NONE>,
+ <0x2 0xc2 0 IRQ_TYPE_NONE>,
+ <0x2 0xc3 0 IRQ_TYPE_NONE>,
+ <0x2 0xc4 0 IRQ_TYPE_NONE>,
+ <0x2 0xc5 0 IRQ_TYPE_NONE>,
+ <0x2 0xc6 0 IRQ_TYPE_NONE>,
+ <0x2 0xc7 0 IRQ_TYPE_NONE>,
+ <0x2 0xc8 0 IRQ_TYPE_NONE>,
+ <0x2 0xc9 0 IRQ_TYPE_NONE>,
+ <0x2 0xca 0 IRQ_TYPE_NONE>,
+ <0x2 0xcb 0 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pmic@3 {
+ compatible = "qcom,pm8150b", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.20.1
