The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
---
drivers/net/phy/adin.c | 117 +++++++++++++++++++++++++++++++++++++++--
1 file changed, 113 insertions(+), 4 deletions(-)
diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
index 4ca685780622..51c0d17577de 100644
--- a/drivers/net/phy/adin.c
+++ b/drivers/net/phy/adin.c
@@ -19,6 +19,10 @@
#define ADIN1300_MII_EXT_REG_PTR 0x0010
#define ADIN1300_MII_EXT_REG_DATA 0x0011
+#define ADIN1300_PHY_CTRL1 0x0012
+#define ADIN1300_AUTO_MDI_EN BIT(10)
+#define ADIN1300_MAN_MDIX_EN BIT(9)
+
#define ADIN1300_INT_MASK_REG 0x0018
#define ADIN1300_INT_MDIO_SYNC_EN BIT(9)
#define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8)
@@ -33,6 +37,9 @@
(ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_HW_IRQ_EN)
#define ADIN1300_INT_STATUS_REG 0x0019
+#define ADIN1300_PHY_STATUS1 0x001a
+#define ADIN1300_PAIR_01_SWAP BIT(11)
+
#define ADIN1300_GE_RGMII_CFG_REG 0xff23
#define ADIN1300_GE_RGMII_RX_MSK GENMASK(8, 6)
#define ADIN1300_GE_RGMII_RX_SEL(x) \
@@ -206,6 +213,8 @@ static int adin_config_init(struct phy_device *phydev)
{
int rc;
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+
rc = genphy_config_init(phydev);
if (rc < 0)
return rc;
@@ -269,13 +278,113 @@ static int adin_write_mmd(struct phy_device *phydev, int devad, u16 regnum,
return __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA, val);
}
+static int adin_config_mdix(struct phy_device *phydev)
+{
+ bool auto_en, mdix_en;
+ int reg;
+
+ mdix_en = false;
+ auto_en = false;
+ switch (phydev->mdix_ctrl) {
+ case ETH_TP_MDI:
+ break;
+ case ETH_TP_MDI_X:
+ mdix_en = true;
+ break;
+ case ETH_TP_MDI_AUTO:
+ auto_en = true;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ reg = phy_read(phydev, ADIN1300_PHY_CTRL1);
+ if (reg < 0)
+ return reg;
+
+ if (mdix_en)
+ reg |= ADIN1300_MAN_MDIX_EN;
+ else
+ reg &= ~ADIN1300_MAN_MDIX_EN;
+
+ if (auto_en)
+ reg |= ADIN1300_AUTO_MDI_EN;
+ else
+ reg &= ~ADIN1300_AUTO_MDI_EN;
+
+ return phy_write(phydev, ADIN1300_PHY_CTRL1, reg);
+}
+
+static int adin_config_aneg(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = adin_config_mdix(phydev);
+ if (ret)
+ return ret;
+
+ return genphy_config_aneg(phydev);
+}
+
+static int adin_mdix_update(struct phy_device *phydev)
+{
+ bool auto_en, mdix_en;
+ bool swapped;
+ int reg;
+
+ reg = phy_read(phydev, ADIN1300_PHY_CTRL1);
+ if (reg < 0)
+ return reg;
+
+ auto_en = !!(reg & ADIN1300_AUTO_MDI_EN);
+ mdix_en = !!(reg & ADIN1300_MAN_MDIX_EN);
+
+ /* If MDI/MDIX is forced, just read it from the control reg */
+ if (!auto_en) {
+ if (mdix_en)
+ phydev->mdix = ETH_TP_MDI_X;
+ else
+ phydev->mdix = ETH_TP_MDI;
+ return 0;
+ }
+
+ /**
+ * Otherwise, we need to deduce it from the PHY status2 reg.
+ * When Auto-MDI is enabled, the ADIN1300_MAN_MDIX_EN bit implies
+ * a preference for MDIX when it is set.
+ */
+ reg = phy_read(phydev, ADIN1300_PHY_STATUS1);
+ if (reg < 0)
+ return reg;
+
+ swapped = !!(reg & ADIN1300_PAIR_01_SWAP);
+
+ if (mdix_en != swapped)
+ phydev->mdix = ETH_TP_MDI_X;
+ else
+ phydev->mdix = ETH_TP_MDI;
+
+ return 0;
+}
+
+static int adin_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = adin_mdix_update(phydev);
+ if (ret < 0)
+ return ret;
+
+ return genphy_read_status(phydev);
+}
+
static struct phy_driver adin_driver[] = {
{
PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200),
.name = "ADIN1200",
.config_init = adin_config_init,
- .config_aneg = genphy_config_aneg,
- .read_status = genphy_read_status,
+ .config_aneg = adin_config_aneg,
+ .read_status = adin_read_status,
.ack_interrupt = adin_phy_ack_intr,
.config_intr = adin_phy_config_intr,
.resume = genphy_resume,
@@ -287,8 +396,8 @@ static struct phy_driver adin_driver[] = {
PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300),
.name = "ADIN1300",
.config_init = adin_config_init,
- .config_aneg = genphy_config_aneg,
- .read_status = genphy_read_status,
+ .config_aneg = adin_config_aneg,
+ .read_status = adin_read_status,
.ack_interrupt = adin_phy_ack_intr,
.config_intr = adin_phy_config_intr,
.resume = genphy_resume,
--
2.20.1
