Based on 'next' branch of Kishon's phy tree (linux-phy). Tested on 'usb-next' of Greg's usb tree. Changes from v4: 1) Separated out the device tree related arch patches from this patch series. Shall be posting these below mentioned patches (which were part of V4 version of this series) in a separate patch series based on Kgene's next branch. [PATCH v4 2/5]dt: exynos5420: Enable support for USB 3.0 PHY controller [PATCH v4 3/5]dt: exynos5420: Enable support for DWC3 controller [PATCH v4 4/5]dt: exynos5250: Enable support for generic USB DRD phy [PATCH v4 5/5]usb-phy: samsung-usb3: Remove older phy-samsung-usb3 driver 2) Also clubbed the reworked VBUS patch for usb3-drd phy, which was earlier sent as a separate patch: [PATCH] phy: exynos5-usbdrd: Add facility to toggle vbus gpio on/off. https://lkml.org/lkml/2014/4/9/186 1) Removed the mention of separate sclk_usbphy30*, instead this clock will be used as 'ref' phy reference clock while adding the device nodes. 2) Reading the PHYCLKRST register to restore any previous settings, instead of using a separate variable for saving/restoring purpose. 3) Renamed 'samsung,syscon-phandle' property to 'samsung,pmu-syscon'. 4) Removed unnecessary check for of_node property at the starting of driver probe, since this is exclusively DT enabled driver. Changes from V3: 1) Separated out the phy init sequences for utmi and pipe3 phys. 2) Changed the nomenclature across the phy to 'usbdrd-phy' to indicate USB 3.0 DRD PHY controller; and thereby changed the names of functions correspondingly, including specific functions for utmi and pipe3 phys. 3) Modified the DT nodes for the updated nomenclature. 4) Using BIT macro for single bit definitions. 5) Keeping track of reference clock after getting till the removal of phy, and getting the ref clock using devm_clk_get() api. 6) Removed aliases for mutiple channel PHYs, and instead using 'samsung,pmu-offset' property for PHY power control register offset. 7) Keeping the phy_init() and phy_power_on() separately in order to align with phy handling in the consumer (DWC3). Changes from v2: 1) Added support for multiple PHYs (UTMI+ and PIPE3) and related changes in the driver structuring. 2) Added a xlate function to get the required phy out of number of PHYs in mutiple PHY scenerio. 3) Changed the names of few structures and variables to have a clearer meaning. 4) Added 'usb3phy_config' structure to take care of mutiple phys for a SoC having 'exynos5_usb3phy_drv_data' driver data. 5) Not deleting support for old driver 'phy-samsung-usb3' until required support for generic phy is added to DWC3. Changes from RFC patch-set: 1) fixes in documentation file - added provision for syscon interface for using PMU register. - added clock names and description - modified description style for 'compatible property' - made usb30_sclk as additional clock rather then making it optional, since it is actually an additional clock for Exynos5420 Soc. 2) fixes in phy-exynos5-usb3 driver file - removed unnecessary #ifndef around KHZ and MHZ definitions - removed 'samsung_cpu_type', 'usb3phy_state' enums; and merged necessary necessary from 'usb3phy_instance' structure to 'usb3phy_driver'. - changed name 'sclk_usbphy30' to 'usb30_sclk_100m' since this is the name indicated as input to the PHY block; and also added (!IS_ERR()) check for using usb30_sclk. - removed unnecessary 'state' check code. - moved 'of_device_id' structure definitions before 'probe()' to avoid unnecessary declaration. - added (pdev->dev.of_node == NULL) check at the starting of probe() - moved 'devm_of_phy_provider_register()' call to end of the probe(). - removed 'label' for usb3drd phy. - corrected macros definition 'PHYCLKRST_MPLL_MULTIPLIER_50M_REF' from 0x02 to 0x32 after confirming same from PHY's data sheet. - replaced pmu register handling, used for power-isolation, with syscon interface api's. - added '.init' and '.exit' callbacks and using them for one time PHY-initialization and deinitialization. - Filtering out the PHY 'power-on' and 'power-off' sequence to '.power_on" and ".power_off" callbacks. - Removed drivers/usb/phy/phy-samsung-usb3.c driver and related code. 3) fixes in dt files - added reference for 'samsung,syscon-phandle' to used for PMU register. - removed second register field which was earlier used for PMU. Vivek Gautam (2): phy: Add new Exynos5 USB 3.0 PHY driver phy: exynos5-usbdrd: Add facility for VBUS supply .../devicetree/bindings/phy/samsung-phy.txt | 40 ++ drivers/phy/Kconfig | 11 + drivers/phy/Makefile | 1 + drivers/phy/phy-exynos5-usbdrd.c | 663 ++++++++++++++++++++ 4 files changed, 715 insertions(+) create mode 100644 drivers/phy/phy-exynos5-usbdrd.c -- 1.7.10.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
