Re: [PATCH v1 1/1] i2c: iproc: Add i2c repeated start capability

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Wolfram,

On 8/6/19 9:09 PM, Rayagonda Kokatanur wrote:
From: Lori Hikichi <lori.hikichi@xxxxxxxxxxxx>

Enable handling of i2c repeated start. The current code
handles a multi msg i2c transfer as separate i2c bus
transactions. This change will now handle this case
using the i2c repeated start protocol. The number of msgs
in a transfer is limited to two, and must be a write
followed by a read.

Signed-off-by: Lori Hikichi <lori.hikichi@xxxxxxxxxxxx>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@xxxxxxxxxxxx>
Signed-off-by: Icarus Chau <icarus.chau@xxxxxxxxxxxx>
Signed-off-by: Ray Jui <ray.jui@xxxxxxxxxxxx>
Signed-off-by: Shivaraj Shetty <sshetty1@xxxxxxxxxxxx>
---

Note this patch has gone through internal review and testing on various I2C slave devices. It is introduced to work around limitation of our I2C controller and allows it to work on certain I2C slave devices that are sensitive and requires repeated start between transactions instead of a stop.

Given that my name is also on the Signed-off-by since I helped to rewrite part of the patch, I'm not going to add my Reviewed-by tag here.

Please help to review.

Thanks,

Ray

  drivers/i2c/busses/i2c-bcm-iproc.c | 70 +++++++++++++++++++++++++++++++-------
  1 file changed, 57 insertions(+), 13 deletions(-)

diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index d7fd76b..15fedcf 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -81,6 +81,7 @@
  #define M_CMD_PROTOCOL_MASK          0xf
  #define M_CMD_PROTOCOL_BLK_WR        0x7
  #define M_CMD_PROTOCOL_BLK_RD        0x8
+#define M_CMD_PROTOCOL_PROCESS       0xa
  #define M_CMD_PEC_SHIFT              8
  #define M_CMD_RD_CNT_SHIFT           0
  #define M_CMD_RD_CNT_MASK            0xff
@@ -675,13 +676,20 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
  	return 0;
  }
-static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
-					 struct i2c_msg *msg)
+/*
+ * If 'process_call' is true, then this is a multi-msg transfer that requires
+ * a repeated start between the messages.
+ * More specifically, it must be a write (reg) followed by a read (data).
+ * The i2c quirks are set to enforce this rule.
+ */
+static int bcm_iproc_i2c_xfer_internal(struct bcm_iproc_i2c_dev *iproc_i2c,
+					struct i2c_msg *msgs, bool process_call)
  {
  	int i;
  	u8 addr;
  	u32 val, tmp, val_intr_en;
  	unsigned int tx_bytes;
+	struct i2c_msg *msg = &msgs[0];
/* check if bus is busy */
  	if (!!(iproc_i2c_rd_reg(iproc_i2c,
@@ -707,14 +715,29 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
  			val = msg->buf[i];
/* mark the last byte */
-			if (i == msg->len - 1)
-				val |= BIT(M_TX_WR_STATUS_SHIFT);
+			if (!process_call && (i == msg->len - 1))
+				val |= 1 << M_TX_WR_STATUS_SHIFT;
iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
  		}
  		iproc_i2c->tx_bytes = tx_bytes;
  	}
+ /* Process the read message if this is process call */
+	if (process_call) {
+		msg++;
+		iproc_i2c->msg = msg;  /* point to second msg */
+
+		/*
+		 * The last byte to be sent out should be a slave
+		 * address with read operation
+		 */
+		addr = msg->addr << 1 | 1;
+		/* mark it the last byte out */
+		val = addr | (1 << M_TX_WR_STATUS_SHIFT);
+		iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
+	}
+
  	/* mark as incomplete before starting the transaction */
  	if (iproc_i2c->irq)
  		reinit_completion(&iproc_i2c->done);
@@ -733,7 +756,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
  	 * underrun interrupt, which will be triggerred when the TX FIFO is
  	 * empty. When that happens we can then pump more data into the FIFO
  	 */
-	if (!(msg->flags & I2C_M_RD) &&
+	if (!process_call && !(msg->flags & I2C_M_RD) &&
  	    msg->len > iproc_i2c->tx_bytes)
  		val_intr_en |= BIT(IE_M_TX_UNDERRUN_SHIFT);
@@ -743,6 +766,8 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
  	 */
  	val = BIT(M_CMD_START_BUSY_SHIFT);
  	if (msg->flags & I2C_M_RD) {
+		u32 protocol;
+
  		iproc_i2c->rx_bytes = 0;
  		if (msg->len > M_RX_FIFO_MAX_THLD_VALUE)
  			iproc_i2c->thld_bytes = M_RX_FIFO_THLD_VALUE;
@@ -758,7 +783,10 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
  		/* enable the RX threshold interrupt */
  		val_intr_en |= BIT(IE_M_RX_THLD_SHIFT);
- val |= (M_CMD_PROTOCOL_BLK_RD << M_CMD_PROTOCOL_SHIFT) |
+		protocol = process_call ?
+				M_CMD_PROTOCOL_PROCESS : M_CMD_PROTOCOL_BLK_RD;
+
+		val |= (protocol << M_CMD_PROTOCOL_SHIFT) |
  		       (msg->len << M_CMD_RD_CNT_SHIFT);
  	} else {
  		val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT);
@@ -774,17 +802,31 @@ static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
  			      struct i2c_msg msgs[], int num)
  {
  	struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(adapter);
-	int ret, i;
+	bool process_call = false;
+	int ret;
- /* go through all messages */
-	for (i = 0; i < num; i++) {
-		ret = bcm_iproc_i2c_xfer_single_msg(iproc_i2c, &msgs[i]);
-		if (ret) {
-			dev_dbg(iproc_i2c->device, "xfer failed\n");
-			return ret;
+	if (num > 2) {
+		dev_err(iproc_i2c->device,
+			"Only support up to 2 messages. Current msg count %d\n",
+			num);
+		return -EOPNOTSUPP;
+	}
+
+	if (num == 2) {
+		/* Repeated start, use process call */
+		process_call = true;
+		if (msgs[1].flags & I2C_M_NOSTART) {
+			dev_err(iproc_i2c->device, "Invalid repeated start\n");
+			return -EOPNOTSUPP;
  		}
  	}
+ ret = bcm_iproc_i2c_xfer_internal(iproc_i2c, msgs, process_call);
+	if (ret) {
+		dev_dbg(iproc_i2c->device, "xfer failed\n");
+		return ret;
+	}
+
  	return num;
  }
@@ -806,6 +848,8 @@ static uint32_t bcm_iproc_i2c_functionality(struct i2c_adapter *adap)
  };
static struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
+	.flags = I2C_AQ_COMB_WRITE_THEN_READ,
+	.max_comb_1st_msg_len = M_TX_RX_FIFO_SIZE,
  	.max_read_len = M_RX_MAX_READ_LEN,
  };



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux