The LED behavior of some Ethernet PHYs is configurable. Add an
optional 'leds' subnode with a child node for each LED to be
configured. The binding aims to be compatible with the common
LED binding (see devicetree/bindings/leds/common.txt).
A LED can be configured to be:
- 'on' when a link is active, some PHYs allow configuration for
certain link speeds
speeds
- 'off'
- blink on RX/TX activity, some PHYs allow configuration for
certain link speeds
For the configuration to be effective it needs to be supported by
the hardware and the corresponding PHY driver.
Suggested-by: Andrew Lunn <andrew@xxxxxxx>
Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
---
Changes in v5:
- renamed triggers from 'phy_link_<speed>_active' to 'phy-link-<speed>'
- added entries for 'phy-link-<speed>-activity'
- added 'phy-link' and 'phy-link-activity' for triggers with any link
speed
- added entry for trigger 'none'
Changes in v4:
- patch added to the series
---
.../devicetree/bindings/net/ethernet-phy.yaml | 59 +++++++++++++++++++
1 file changed, 59 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
index f70f18ff821f..98ba320f828b 100644
--- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
@@ -153,6 +153,50 @@ properties:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
+patternProperties:
+ "^leds$":
+ type: object
+ description:
+ Subnode with configuration of the PHY LEDs.
+
+ patternProperties:
+ "^led@[0-9]+$":
+ type: object
+ description:
+ Subnode with the configuration of a single PHY LED.
+
+ properties:
+ reg:
+ description:
+ The ID number of the LED, typically corresponds to a hardware ID.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ linux,default-trigger:
+ description:
+ This parameter, if present, is a string specifying the trigger
+ assigned to the LED. Supported triggers are:
+ "none" - LED will be solid off
+ "phy-link" - LED will be solid on when a link is active
+ "phy-link-10m" - LED will be solid on when a 10Mb/s link is active
+ "phy-link-100m" - LED will be solid on when a 100Mb/s link is active
+ "phy-link-1g" - LED will be solid on when a 1Gb/s link is active
+ "phy-link-10g" - LED will be solid on when a 10Gb/s link is active
+ "phy-link-activity" - LED will be on when link is active and blink
+ off with activity.
+ "phy-link-10m-activity" - LED will be on when 10Mb/s link is active
+ and blink off with activity.
+ "phy-link-100m-activity" - LED will be on when 100Mb/s link is
+ active and blink off with activity.
+ "phy-link-1g-activity" - LED will be on when 1Gb/s link is active
+ and blink off with activity.
+ "phy-link-10g-activity" - LED will be on when 10Gb/s link is active
+ and blink off with activity.
+
+ $ref: "/schemas/types.yaml#/definitions/string"
+
+ required:
+ - reg
+
required:
- reg
@@ -173,5 +217,20 @@ examples:
reset-gpios = <&gpio1 4 1>;
reset-assert-us = <1000>;
reset-deassert-us = <2000>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ linux,default-trigger = "phy-link-1g";
+ };
+
+ led@1 {
+ reg = <1>;
+ linux,default-trigger = "phy-link-100m-activity";
+ };
+ };
};
};
--
2.22.0.770.g0f2c4a37fd-goog
