Add minimal thermal zone for two temperature sensor One is located close to the DDR and the other one is located close to the PLLs (between the CPU and GPU) Signed-off-by: Guillaume La Roque <glaroque@xxxxxxxxxxxx> --- .../boot/dts/amlogic/meson-g12a-sei510.dts | 56 +++++++++++++++++++ 1 file changed, 56 insertions(+) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts index 979449968a5f..2c16a2cba0a3 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts @@ -10,6 +10,7 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/meson-g12a-gpio.h> #include <dt-bindings/sound/meson-g12a-tohdmitx.h> +#include <dt-bindings/thermal/thermal.h> / { compatible = "seirobotics,sei510", "amlogic,g12a"; @@ -33,6 +34,53 @@ ethernet0 = ðmac; }; + thermal-zones { + cpu-thermal { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&cpu_temp>; + + trips { + cpu_critical: cpu-critical { + temperature = <110000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map { + trip = <&cpu_critical>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + ddr-thermal { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&ddr_temp>; + + trips { + ddr_critical: ddr-critical { + temperature = <110000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map { + trip = <&ddr_critical>; + cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + mono_dac: audio-codec-0 { compatible = "maxim,max98357a"; #sound-dai-cells = <0>; @@ -321,6 +369,7 @@ operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPU_CLK>; clock-latency = <50000>; + #cooling-cells = <2>; }; &cpu1 { @@ -328,6 +377,7 @@ operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPU_CLK>; clock-latency = <50000>; + #cooling-cells = <2>; }; &cpu2 { @@ -335,6 +385,7 @@ operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPU_CLK>; clock-latency = <50000>; + #cooling-cells = <2>; }; &cpu3 { @@ -342,6 +393,7 @@ operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPU_CLK>; clock-latency = <50000>; + #cooling-cells = <2>; }; &cvbs_vdac_port { @@ -368,6 +420,10 @@ status = "okay"; }; +&mali { + #cooling-cells = <2>; +}; + &hdmi_tx { status = "okay"; pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; -- 2.17.1