On Mon, 2019-08-05 at 16:21 +0200, Andrew Lunn wrote:
> [External]
>
> On Mon, Aug 05, 2019 at 07:54:40PM +0300, Alexandru Ardelean wrote:
> > This change adds support for enabling PHY interrupts that can be used by
> > the PHY framework to get signal for link/speed/auto-negotiation changes.
> >
> > Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
> > ---
> > drivers/net/phy/adin.c | 44 ++++++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 44 insertions(+)
> >
> > diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> > index c100a0dd95cd..b75c723bda79 100644
> > --- a/drivers/net/phy/adin.c
> > +++ b/drivers/net/phy/adin.c
> > @@ -14,6 +14,22 @@
> > #define PHY_ID_ADIN1200 0x0283bc20
> > #define PHY_ID_ADIN1300 0x0283bc30
> >
> > +#define ADIN1300_INT_MASK_REG 0x0018
> > +#define ADIN1300_INT_MDIO_SYNC_EN BIT(9)
> > +#define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8)
> > +#define ADIN1300_INT_ANEG_PAGE_RX_EN BIT(6)
> > +#define ADIN1300_INT_IDLE_ERR_CNT_EN BIT(5)
> > +#define ADIN1300_INT_MAC_FIFO_OU_EN BIT(4)
> > +#define ADIN1300_INT_RX_STAT_CHNG_EN BIT(3)
> > +#define ADIN1300_INT_LINK_STAT_CHNG_EN BIT(2)
> > +#define ADIN1300_INT_SPEED_CHNG_EN BIT(1)
> > +#define ADIN1300_INT_HW_IRQ_EN BIT(0)
> > +#define ADIN1300_INT_MASK_EN \
> > + (ADIN1300_INT_ANEG_STAT_CHNG_EN | ADIN1300_INT_ANEG_PAGE_RX_EN | \
> > + ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_SPEED_CHNG_EN | \
> > + ADIN1300_INT_HW_IRQ_EN)
> > +#define ADIN1300_INT_STATUS_REG 0x0019
> > +
> > static int adin_config_init(struct phy_device *phydev)
> > {
> > int rc;
> > @@ -25,15 +41,40 @@ static int adin_config_init(struct phy_device *phydev)
> > return 0;
> > }
> >
> > +static int adin_phy_ack_intr(struct phy_device *phydev)
> > +{
> > + int ret;
> > +
> > + /* Clear pending interrupts. */
> > + ret = phy_read(phydev, ADIN1300_INT_STATUS_REG);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
>
> Please go through the whole driver and throw out all the needless
ack;
i'll re-visit;
>
> if (ret < 0)
> return ret;
>
> return 0;
>
> Thanks
> Andrew
