Re: [PATCH v2 4/6] irqchip/irq-pruss-intc: Add helper functions to configure internal mapping

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 8/1/19 12:10 PM, Suman Anna wrote:
Hi Marc,

On 8/1/19 3:45 AM, Marc Zyngier wrote:
On 31/07/2019 23:41, Suman Anna wrote:
The PRUSS INTC receives a number of system input interrupt source events
and supports individual control configuration and hardware prioritization.
These input events can be mapped to some output interrupt lines through 2
levels of many-to-one mapping i.e. events to channel mapping and channels
to output interrupts.

This mapping information is provided through the PRU firmware that is
loaded onto a PRU core/s or through the device tree node of the PRU
application. The mapping is configured by the PRU remoteproc driver, and
is setup before the PRU core is started and cleaned up after the PRU core
is stopped. This event mapping configuration logic programs the Channel
Map Registers (CMRx) and Host-Interrupt Map Registers (HMRx) only when a
new program is being loaded/started and the same events and interrupt
channels are reset to zero when stopping a PRU.

Add two helper functions: pruss_intc_configure() & pruss_intc_unconfigure()
that the PRU remoteproc driver can use to configure the PRUSS INTC.

So let me see if I correctly understand this: this adds yet another
firmware description parser, with a private interface to another
(undisclosed?) driver, bypassing the standard irqchip configuration
mechanism. It sounds great, doesn't it?

What I cannot really infer from this message (-ETOOMUCHJARGON) is what
interrupts this affects:

- Interrupts from random devices to the PRUSS?
- Interrupts from the PRUSS to the host?
- Something else?

The interrupt sources (called system events) can be from internal PRUSS
peripherals, SoC-level peripherals or just software triggering (limited
to some events).

So, the PRUSS INTC behaves as a funnel and is both an interrupt router
and multiplexer. The INTC itself is part of the PRUSS, and all PRU
application related interrupts/events that need to trigger an interrupt
to either the PRU cores or other host processors (like DSP, ARM) have to
go through this INTC, and routed out to a limited number of output
interrupts that are then connected to different processors.

The split of interrupt handling between a PRU and its peer host
processor will be a application design choice (We can implement soft IPs
like UARTs, ADCs, I2Cs etc using PRUs). Some of the input events
themselves are multiplexed and controlled by a single MMR (outside of
INTC) that feeds different sets of events into the INTC. The MMR
configuration is outside of scope of this driver and will depend on the
application/client driver being run.


When does this happen? Under control of what? It isn't even clear why
this is part of this irqchip driver.

The mapping configuration is per PRU application and firmware, and is
done in line with acquiring and release a PRU which is treated as an
exclusive resource. We establish the mapping for all events through this
driver including the events that are to be routed to PRUs. This is done
to save the tiny/limited Instruction RAM space that PRUs have.

We have designed this as an irqchip driver (instead of some custom SoC
driver exporting custom functions) to use standard Linux semantics/irq
API and better integrate with Linux DT, but we need some semantics for
establishing the routing at runtime depending on the PRU client driver
we are running. The exported functions will be called only by the PRU
remoteproc driver during a pru_rproc_get()/pru_rproc_put(), and are
transparent to PRU client drivers.

Please also see the discussion from v1 [1] on why we can't use an
extended number of interrupt-cells infrastructure for achieving this.

[1] https://patchwork.kernel.org/patch/11034563/


Depending what this does, there may be ways to fit it into the standard
interrupt configuration framework. After all, we already have standard
interfaces to route interrupts to virtual CPUs, effectively passing full
control of an interrupt to another entity. If you squint hard enough,
your PRUSS can fit that description.

Yeah, I am open to suggestions if there is a better way of doing this.

Hi Suman,

Can you explain more about the use case where one PRU system event is
mapped to multiple host events?

I have an idea that we can use multiple struct irq_domains to make this
work in the existing IRQ framework, but it would be helpful to know more
about the bigger picture first.


regards
Suman


If that doesn't work, then we need to make the IRQ framework grok that
kind of requirement (hence my request for clarification). But I'm
strongly opposed to inventing a SoC-private way of configuring
interrupts behind the kernel's back.

Thanks,

	M.






[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux