Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
---
.../devicetree/bindings/timer/renesas,cmt.txt | 49 ++++++++++++++++
drivers/clocksource/sh_cmt.c | 66 ++++++++++++++++------
2 files changed, 97 insertions(+), 18 deletions(-)
create mode 100644 Documentation/devicetree/bindings/timer/renesas,cmt.txt
As explained in the cover letter, compared to v1 I've dropped the channel
subnodes from the DT bindings and just use a channels mask, as I don't need to
specify per-channel properties. I'm slightly uncertain about this change
though, as I can't easily predict whether per-channel properties would be
needed later for new hardware. It won't be difficult to reintroduce channel
subnodes then, so I'd rather not clutter the DT bindings with channel subnodes
now. Please feel free to disagree.
diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt
new file mode 100644
index 0000000..d6a82cd
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt
@@ -0,0 +1,49 @@
+* Renesas R-Car Compare Match Timer (CMT)
+
+The CMT is a multi-channel 16/32/48-bit timer/counter with configurable clock
+inputs and programmable compare match.
+
+Channels share hardware resources but their counter and compare match value
+are independent. A particular CMT instance can implement only a subset of the
+channels supported by the CMT model. Channel indices represent the hardware
+position of the channel in the CMT and don't match the channel numbers in the
+datasheets.
+
+Required Properties:
+
+ - compatible: must contain one of the following.
+ - "renesas,cmt-32" for the 32-bit CMT
+ (CMT0 on sh7372, sh73a0 and r8a7740)
+ - "renesas,cmt-32-fast" for the 32-bit CMT with fast clock support
+ (CMT[234] on sh7372, sh73a0 and r8a7740)
+ - "renasas,cmt-48" for the 48-bit CMT
+ (CMT1 on sh7372, sh73a0 and r8a7740)
+ - "renesas,cmt-48-gen2" for the second generation 48-bit CMT
+ (CMT[01] on r8a73a4, r8a7790 and r8a7791)
+
+ - reg: base address and length of the registers block for the timer module.
+ - interrupt-parent, interrupts: interrupt-specifier for the timer, one per
+ channel.
+ - clocks: a list of phandle + clock-specifier pairs, one for each entry
+ in clock-names.
+ - clock-names: must contain "fck" for the functional clock.
+
+ - renesas,channels-mask: bitmask of the available channels.
+
+
+Example: R8A7790 (R-Car H2) CMT0 node
+
+ CMT0 on R8A7790 implements hardware channels 5 and 6 only and names
+ them channels 0 and 1 in the documentation.
+
+ cmt0: timer@ffca0000 {
+ compatible = "renesas,cmt-48-gen2";
+ reg = <0 0xffca0000 0 0x1004>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>,
+ <0 142 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp1_clks R8A7790_CLK_CMT0>;
+ clock-names = "fck";
+
+ renesas,channels-mask = <0x60>;
+ };
diff --git a/drivers/clocksource/sh_cmt.c b/drivers/clocksource/sh_cmt.c
index 4d00e4b..3a27ce3 100644
--- a/drivers/clocksource/sh_cmt.c
+++ b/drivers/clocksource/sh_cmt.c
@@ -24,6 +24,7 @@
#include <linux/ioport.h>
#include <linux/irq.h>
#include <linux/module.h>
+#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pm_domain.h>
#include <linux/pm_runtime.h>
@@ -122,6 +123,7 @@ struct sh_cmt_device {
struct sh_cmt_channel *channels;
unsigned int num_channels;
+ unsigned int hw_channels;
bool has_clockevent;
bool has_clocksource;
@@ -924,10 +926,35 @@ static int sh_cmt_map_memory(struct sh_cmt_device *cmt)
return 0;
}
+static const struct platform_device_id sh_cmt_id_table[] = {
+ { "sh-cmt-16", (kernel_ulong_t)&sh_cmt_info[SH_CMT_16BIT] },
+ { "sh-cmt-32", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT] },
+ { "sh-cmt-32-fast", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT_FAST] },
+ { "sh-cmt-48", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT] },
+ { "sh-cmt-48-gen2", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT_GEN2] },
+ { }
+};
+MODULE_DEVICE_TABLE(platform, sh_cmt_id_table);
+
+static const struct of_device_id sh_cmt_of_table[] = {
+ { .compatible = "renesas,cmt-32", .data = &sh_cmt_info[SH_CMT_32BIT] },
+ { .compatible = "renesas,cmt-32-fast", .data = &sh_cmt_info[SH_CMT_32BIT_FAST] },
+ { .compatible = "renasas,cmt-48", .data = &sh_cmt_info[SH_CMT_48BIT] },
+ { .compatible = "renesas,cmt-48-gen2", .data = &sh_cmt_info[SH_CMT_48BIT_GEN2] },
+ { }
+};
+MODULE_DEVICE_TABLE(of, sh_cmt_of_table);
+
+static int sh_cmt_parse_dt(struct sh_cmt_device *cmt)
+{
+ struct device_node *np = cmt->pdev->dev.of_node;
+
+ return of_property_read_u32(np, "renesas,channels-mask",
+ &cmt->hw_channels);
+}
+
static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev)
{
- struct sh_timer_config *cfg = pdev->dev.platform_data;
- const struct platform_device_id *id = pdev->id_entry;
unsigned int mask;
unsigned int i;
int ret;
@@ -936,13 +963,26 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev)
cmt->pdev = pdev;
raw_spin_lock_init(&cmt->lock);
- if (!cfg) {
+ if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
+ const struct of_device_id *id;
+
+ id = of_match_node(sh_cmt_of_table, pdev->dev.of_node);
+ cmt->info = id->data;
+
+ ret = sh_cmt_parse_dt(cmt);
+ if (ret < 0)
+ return ret;
+ } else if (pdev->dev.platform_data) {
+ struct sh_timer_config *cfg = pdev->dev.platform_data;
+ const struct platform_device_id *id = pdev->id_entry;
+
+ cmt->info = (const struct sh_cmt_info *)id->driver_data;
+ cmt->hw_channels = cfg->channels_mask;
+ } else {
dev_err(&cmt->pdev->dev, "missing platform data\n");
return -ENXIO;
}
- cmt->info = (const struct sh_cmt_info *)id->driver_data;
-
/* Get hold of clock. */
cmt->clk = clk_get(&cmt->pdev->dev, "fck");
if (IS_ERR(cmt->clk)) {
@@ -960,8 +1000,7 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev)
goto err_clk_unprepare;
/* Allocate and setup the channels. */
- cmt->num_channels = hweight8(cfg->channels_mask);
-
+ cmt->num_channels = hweight8(cmt->hw_channels);
cmt->channels = kzalloc(cmt->num_channels * sizeof(*cmt->channels),
GFP_KERNEL);
if (cmt->channels == NULL) {
@@ -973,7 +1012,7 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev)
* Use the first channel as a clock event device and the second channel
* as a clock source. If only one channel is available use it for both.
*/
- for (i = 0, mask = cfg->channels_mask; i < cmt->num_channels; ++i) {
+ for (i = 0, mask = cmt->hw_channels; i < cmt->num_channels; ++i) {
unsigned int hwidx = ffs(mask) - 1;
bool clocksource = i == 1 || cmt->num_channels == 1;
bool clockevent = i == 0;
@@ -1044,21 +1083,12 @@ static int sh_cmt_remove(struct platform_device *pdev)
return -EBUSY; /* cannot unregister clockevent and clocksource */
}
-static const struct platform_device_id sh_cmt_id_table[] = {
- { "sh-cmt-16", (kernel_ulong_t)&sh_cmt_info[SH_CMT_16BIT] },
- { "sh-cmt-32", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT] },
- { "sh-cmt-32-fast", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT_FAST] },
- { "sh-cmt-48", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT] },
- { "sh-cmt-48-gen2", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT_GEN2] },
- { }
-};
-MODULE_DEVICE_TABLE(platform, sh_cmt_id_table);
-
static struct platform_driver sh_cmt_device_driver = {
.probe = sh_cmt_probe,
.remove = sh_cmt_remove,
.driver = {
.name = "sh_cmt",
+ .of_match_table = of_match_ptr(sh_cmt_of_table),
},
.id_table = sh_cmt_id_table,
};
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
