Re: [PATCH] arm64: dts: qcom: msm8998: Node ordering, address cleanups

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 22-07-19, 09:58, Jeffrey Hugo wrote:
> DT nodes should be ordered by address, then node name, and finally label.
> The msm8998 dtsi does not follow this, so clean it up by reordering the
> nodes.  While we are at it, extend the addresses to be fully 32-bits wide
> so that ordering is easy to determine when adding new nodes.  Also, two
> or so nodes had the wrong address value in their node name (did not match
> the reg property), so fix those up as well.
> 
> Hopefully going forward, things can be maintained so that a cleanup like
> this is not needed.

lgtm, ideally I would have liked that we reg addresses fixed first and
then sort the file (remember a patch should do one thing)

But then any cleanup is better to do :) so:

Reviewed-by: Vinod Koul <vkoul@xxxxxxxxxx>

> 
> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@xxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/msm8998.dtsi | 254 +++++++++++++-------------
>  1 file changed, 127 insertions(+), 127 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> index c13ed7aeb1e0..4b66a1c588f8 100644
> --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> @@ -787,14 +787,22 @@
>  		ranges = <0 0 0 0xffffffff>;
>  		compatible = "simple-bus";
>  
> -		rpm_msg_ram: memory@68000 {
> +		gcc: clock-controller@100000 {
> +			compatible = "qcom,gcc-msm8998";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +			reg = <0x00100000 0xb0000>;
> +		};
> +
> +		rpm_msg_ram: memory@778000 {
>  			compatible = "qcom,rpm-msg-ram";
> -			reg = <0x778000 0x7000>;
> +			reg = <0x00778000 0x7000>;
>  		};
>  
>  		qfprom: qfprom@780000 {
>  			compatible = "qcom,qfprom";
> -			reg = <0x780000 0x621c>;
> +			reg = <0x00780000 0x621c>;
>  			#address-cells = <1>;
>  			#size-cells = <1>;
>  
> @@ -804,47 +812,10 @@
>  			};
>  		};
>  
> -		gcc: clock-controller@100000 {
> -			compatible = "qcom,gcc-msm8998";
> -			#clock-cells = <1>;
> -			#reset-cells = <1>;
> -			#power-domain-cells = <1>;
> -			reg = <0x100000 0xb0000>;
> -		};
> -
> -		tlmm: pinctrl@3400000 {
> -			compatible = "qcom,msm8998-pinctrl";
> -			reg = <0x3400000 0xc00000>;
> -			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> -			gpio-controller;
> -			#gpio-cells = <0x2>;
> -			interrupt-controller;
> -			#interrupt-cells = <0x2>;
> -		};
> -
> -		spmi_bus: spmi@800f000 {
> -			compatible = "qcom,spmi-pmic-arb";
> -			reg =	<0x800f000 0x1000>,
> -				<0x8400000 0x1000000>,
> -				<0x9400000 0x1000000>,
> -				<0xa400000 0x220000>,
> -				<0x800a000 0x3000>;
> -			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> -			interrupt-names = "periph_irq";
> -			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
> -			qcom,ee = <0>;
> -			qcom,channel = <0>;
> -			#address-cells = <2>;
> -			#size-cells = <0>;
> -			interrupt-controller;
> -			#interrupt-cells = <4>;
> -			cell-index = <0>;
> -		};
> -
>  		tsens0: thermal@10ab000 {
>  			compatible = "qcom,msm8998-tsens", "qcom,tsens-v2";
> -			reg = <0x10ab000 0x1000>, /* TM */
> -			      <0x10aa000 0x1000>; /* SROT */
> +			reg = <0x010ab000 0x1000>, /* TM */
> +			      <0x010aa000 0x1000>; /* SROT */
>  
>  			#qcom,sensors = <14>;
>  			#thermal-sensor-cells = <1>;
> @@ -852,8 +823,8 @@
>  
>  		tsens1: thermal@10ae000 {
>  			compatible = "qcom,msm8998-tsens", "qcom,tsens-v2";
> -			reg = <0x10ae000 0x1000>, /* TM */
> -			      <0x10ad000 0x1000>; /* SROT */
> +			reg = <0x010ae000 0x1000>, /* TM */
> +			      <0x010ad000 0x1000>; /* SROT */
>  
>  			#qcom,sensors = <8>;
>  			#thermal-sensor-cells = <1>;
> @@ -943,16 +914,107 @@
>  			};
>  		};
>  
> +		ufshc: ufshc@1da4000 {
> +			compatible = "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
> +			reg = <0x01da4000 0x2500>;
> +			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> +			phys = <&ufsphy_lanes>;
> +			phy-names = "ufsphy";
> +			lanes-per-direction = <2>;
> +			power-domains = <&gcc UFS_GDSC>;
> +			#reset-cells = <1>;
> +
> +			clock-names =
> +				"core_clk",
> +				"bus_aggr_clk",
> +				"iface_clk",
> +				"core_clk_unipro",
> +				"ref_clk",
> +				"tx_lane0_sync_clk",
> +				"rx_lane0_sync_clk",
> +				"rx_lane1_sync_clk";
> +			clocks =
> +				<&gcc GCC_UFS_AXI_CLK>,
> +				<&gcc GCC_AGGRE1_UFS_AXI_CLK>,
> +				<&gcc GCC_UFS_AHB_CLK>,
> +				<&gcc GCC_UFS_UNIPRO_CORE_CLK>,
> +				<&rpmcc RPM_SMD_LN_BB_CLK1>,
> +				<&gcc GCC_UFS_TX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_RX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_RX_SYMBOL_1_CLK>;
> +			freq-table-hz =
> +				<50000000 200000000>,
> +				<0 0>,
> +				<0 0>,
> +				<37500000 150000000>,
> +				<0 0>,
> +				<0 0>,
> +				<0 0>,
> +				<0 0>;
> +
> +			resets = <&gcc GCC_UFS_BCR>;
> +			reset-names = "rst";
> +		};
> +
> +		ufsphy: phy@1da7000 {
> +			compatible = "qcom,msm8998-qmp-ufs-phy";
> +			reg = <0x01da7000 0x18c>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			clock-names =
> +				"ref",
> +				"ref_aux";
> +			clocks =
> +				<&gcc GCC_UFS_CLKREF_CLK>,
> +				<&gcc GCC_UFS_PHY_AUX_CLK>;
> +
> +			reset-names = "ufsphy";
> +			resets = <&ufshc 0>;
> +
> +			ufsphy_lanes: lanes@1da7400 {
> +				reg = <0x01da7400 0x128>,
> +				      <0x01da7600 0x1fc>,
> +				      <0x01da7c00 0x1dc>,
> +				      <0x01da7800 0x128>,
> +				      <0x01da7a00 0x1fc>;
> +				#phy-cells = <0>;
> +			};
> +		};
> +
>  		tcsr_mutex_regs: syscon@1f40000 {
>  			compatible = "syscon";
> -			reg = <0x1f40000 0x20000>;
> +			reg = <0x01f40000 0x20000>;
>  		};
>  
> -		apcs_glb: mailbox@9820000 {
> -			compatible = "qcom,msm8998-apcs-hmss-global";
> -			reg = <0x17911000 0x1000>;
> +		tlmm: pinctrl@3400000 {
> +			compatible = "qcom,msm8998-pinctrl";
> +			reg = <0x03400000 0xc00000>;
> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			#gpio-cells = <0x2>;
> +			interrupt-controller;
> +			#interrupt-cells = <0x2>;
> +		};
>  
> -			#mbox-cells = <1>;
> +		spmi_bus: spmi@800f000 {
> +			compatible = "qcom,spmi-pmic-arb";
> +			reg =	<0x0800f000 0x1000>,
> +				<0x08400000 0x1000000>,
> +				<0x09400000 0x1000000>,
> +				<0x0a400000 0x220000>,
> +				<0x0800a000 0x3000>;
> +			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> +			interrupt-names = "periph_irq";
> +			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
> +			qcom,ee = <0>;
> +			qcom,channel = <0>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +			interrupt-controller;
> +			#interrupt-cells = <4>;
> +			cell-index = <0>;
>  		};
>  
>  		usb3: usb@a8f8800 {
> @@ -1044,7 +1106,7 @@
>  
>  		sdhc2: sdhci@c0a4900 {
>  			compatible = "qcom,sdhci-msm-v4";
> -			reg = <0xc0a4900 0x314>, <0xc0a4000 0x800>;
> +			reg = <0x0c0a4900 0x314>, <0x0c0a4000 0x800>;
>  			reg-names = "hc_mem", "core_mem";
>  
>  			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> @@ -1149,6 +1211,16 @@
>  			#size-cells = <0>;
>  		};
>  
> +		blsp2_uart1: serial@c1b0000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x0c1b0000 0x1000>;
> +			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>,
> +				 <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			status = "disabled";
> +		};
> +
>  		blsp2_i2c0: i2c@c1b5000 {
>  			compatible = "qcom,i2c-qup-v2.2.1";
>  			reg = <0x0c1b5000 0x600>;
> @@ -1239,14 +1311,11 @@
>  			#size-cells = <0>;
>  		};
>  
> -		blsp2_uart1: serial@c1b0000 {
> -			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> -			reg = <0xc1b0000 0x1000>;
> -			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> -			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>,
> -				 <&gcc GCC_BLSP2_AHB_CLK>;
> -			clock-names = "core", "iface";
> -			status = "disabled";
> +		apcs_glb: mailbox@17911000 {
> +			compatible = "qcom,msm8998-apcs-hmss-global";
> +			reg = <0x17911000 0x1000>;
> +
> +			#mbox-cells = <1>;
>  		};
>  
>  		timer@17920000 {
> @@ -1320,75 +1389,6 @@
>  			redistributor-stride = <0x0 0x20000>;
>  			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>  		};
> -
> -		ufshc: ufshc@1da4000 {
> -			compatible = "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
> -			reg = <0x01da4000 0x2500>;
> -			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> -			phys = <&ufsphy_lanes>;
> -			phy-names = "ufsphy";
> -			lanes-per-direction = <2>;
> -			power-domains = <&gcc UFS_GDSC>;
> -			#reset-cells = <1>;
> -
> -			clock-names =
> -				"core_clk",
> -				"bus_aggr_clk",
> -				"iface_clk",
> -				"core_clk_unipro",
> -				"ref_clk",
> -				"tx_lane0_sync_clk",
> -				"rx_lane0_sync_clk",
> -				"rx_lane1_sync_clk";
> -			clocks =
> -				<&gcc GCC_UFS_AXI_CLK>,
> -				<&gcc GCC_AGGRE1_UFS_AXI_CLK>,
> -				<&gcc GCC_UFS_AHB_CLK>,
> -				<&gcc GCC_UFS_UNIPRO_CORE_CLK>,
> -				<&rpmcc RPM_SMD_LN_BB_CLK1>,
> -				<&gcc GCC_UFS_TX_SYMBOL_0_CLK>,
> -				<&gcc GCC_UFS_RX_SYMBOL_0_CLK>,
> -				<&gcc GCC_UFS_RX_SYMBOL_1_CLK>;
> -			freq-table-hz =
> -				<50000000 200000000>,
> -				<0 0>,
> -				<0 0>,
> -				<37500000 150000000>,
> -				<0 0>,
> -				<0 0>,
> -				<0 0>,
> -				<0 0>;
> -
> -			resets = <&gcc GCC_UFS_BCR>;
> -			reset-names = "rst";
> -		};
> -
> -		ufsphy: phy@1da7000 {
> -			compatible = "qcom,msm8998-qmp-ufs-phy";
> -			reg = <0x01da7000 0x18c>;
> -			#address-cells = <1>;
> -			#size-cells = <1>;
> -			ranges;
> -
> -			clock-names =
> -				"ref",
> -				"ref_aux";
> -			clocks =
> -				<&gcc GCC_UFS_CLKREF_CLK>,
> -				<&gcc GCC_UFS_PHY_AUX_CLK>;
> -
> -			reset-names = "ufsphy";
> -			resets = <&ufshc 0>;
> -
> -			ufsphy_lanes: lanes@1da7400 {
> -				reg = <0x01da7400 0x128>,
> -				      <0x01da7600 0x1fc>,
> -				      <0x01da7c00 0x1dc>,
> -				      <0x01da7800 0x128>,
> -				      <0x01da7a00 0x1fc>;
> -				#phy-cells = <0>;
> -			};
> -		};
>  	};
>  };
>  
> -- 
> 2.17.1

-- 
~Vinod



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux