On Wed, Jul 17, 2019 at 2:26 PM Tushar Khandelwal
<tushar.khandelwal@xxxxxxx> wrote:
> diff --git a/Documentation/devicetree/bindings/mailbox/arm,mhuv2.txt b/Documentation/devicetree/bindings/mailbox/arm,mhuv2.txt
> new file mode 100644
> index 000000000000..3a05593414bc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mailbox/arm,mhuv2.txt
> @@ -0,0 +1,108 @@
> +Arm MHUv2 Mailbox Driver
> +========================
> +
> +The Arm Message-Handling-Unit (MHU) Version 2 is a mailbox controller that has
> +between 1 and 124 channel windows to provide unidirectional communication with
> +remote processor(s).
> +
> +Given the unidirectional nature of the device, an MHUv2 mailbox may only be
> +written to or read from. If a pair of MHU devices is implemented between two
> +processing elements to provide bidirectional communication, these must be
> +specified as two separate mailboxes.
> +
> +A device tree node for an Arm MHUv2 device must specify either a receiver frame
> +or a sender frame, indicating which end of the unidirectional MHU device which
> +the device node entry describes.
> +
> +An MHU device must be specified with a transport protocol. The transport
> +protocol of an MHU device determines the method of data transmission as well as
> +the number of provided mailboxes.
> +Following are the possible transport protocol types:
> +- Single-word: An MHU device implements as many mailboxes as it
> + provides channel windows. Data is transmitted through
> + the MHU registers.
> +- Multi-word: An MHU device implements a single mailbox. All channel windows
> + will be used during transmission. Data is transmitted through
> + the MHU registers.
> +- Doorbell: An MHU device implements as many mailboxes as there are flag
> + bits available in its channel windows. Optionally, data may
> + be transmitted through a shared memory region, wherein the MHU
> + is used strictly as an interrupt generation mechanism.
> +
> +Mailbox Device Node:
> +====================
> +
> +Required properties:
> +--------------------
> +- compatible: Shall be "arm,mhuv2" & "arm,primecell"
> +- reg: Contains the mailbox register address range (base
> + address and length)
> +- #mbox-cells Shall be 1 - the index of the channel needed.
> +- mhu-frame Frame type of the device.
> + Shall be either "sender" or "receiver"
> +- mhu-protocol Transport protocol of the device. Shall be one of the
> + following: "single-word", "multi-word", "doorbell"
> +
> +Required properties (receiver frame):
> +-------------------------------------
> +- interrupts: Contains the interrupt information corresponding to the
> + combined interrupt of the receiver frame
> +
> +Example:
> +--------
> +
> + mbox_mw_tx: mhu@10000000 {
> + compatible = "arm,mhuv2","arm,primecell";
> + reg = <0x10000000 0x1000>;
> + clocks = <&refclk100mhz>;
> + clock-names = "apb_pclk";
> + #mbox-cells = <1>;
> + mhu-protocol = "multi-word";
> + mhu-frame = "sender";
> + };
> +
> + mbox_sw_tx: mhu@10000000 {
> + compatible = "arm,mhuv2","arm,primecell";
> + reg = <0x11000000 0x1000>;
> + clocks = <&refclk100mhz>;
> + clock-names = "apb_pclk";
> + #mbox-cells = <1>;
> + mhu-protocol = "single-word";
> + mhu-frame = "sender";
> + };
> +
> + mbox_db_rx: mhu@10000000 {
> + compatible = "arm,mhuv2","arm,primecell";
> + reg = <0x12000000 0x1000>;
> + clocks = <&refclk100mhz>;
> + clock-names = "apb_pclk";
> + #mbox-cells = <1>;
> + interrupts = <0 45 4>;
> + interrupt-names = "mhu_rx";
> + mhu-protocol = "doorbell";
> + mhu-frame = "receiver";
> + };
> +
> + mhu_client: scb@2e000000 {
> + compatible = "fujitsu,mb86s70-scb-1.0";
> + reg = <0 0x2e000000 0x4000>;
> + mboxes =
> + // For multi-word frames, client may only instantiate a single
> + // mailbox for a mailbox controller
> + <&mbox_mw_tx 0>,
> +
> + // For single-word frames, client may instantiate as many
> + // mailboxes as there are channel windows in the MHU
> + <&mbox_sw_tx 0>,
> + <&mbox_sw_tx 1>,
> + <&mbox_sw_tx 2>,
> + <&mbox_sw_tx 3>,
> +
> + // For doorbell frames, client may instantiate as many mailboxes
> + // as there are bits available in the combined number of channel
> + // windows ((channel windows * 32) mailboxes)
> + <mbox_db_rx 0>,
> + <mbox_db_rx 1>,
> + ...
> + <mbox_db_rx 17>;
> + };
If the mhuv2 instance implements, say, 3 channel windows between
sender (linux) and receiver (firmware), and Linux runs two protocols
each requiring 1 and 2-word sized messages respectively. The hardware
supports that by assigning windows [0] and [1,2] to each protocol.
However, I don't think the driver can support that. Or does it?
Also I see problem with implementing "protocol modes" in the
controller driver - 'mhu-protocol' property should go away. And
'mhu-frame' is unncessary - presence of interrupt property could imply
'receiver', otherwise 'sender'.
Cheers!
