On Thu, Jul 18, 2019 at 10:47:16, Jonathan Chocron <jonnyc@xxxxxxxxxx>
wrote:
> This driver is DT based and utilizes the DesignWare APIs.
> It allows using a smaller ECAM range for a larger bus range -
> usually an entire bus uses 1MB of address space, but the driver
> can use it for a larger number of buses.
>
> All link initializations are handled by the boot FW.
>
> Signed-off-by: Jonathan Chocron <jonnyc@xxxxxxxxxx>
> ---
> drivers/pci/controller/dwc/Kconfig | 12 +
> drivers/pci/controller/dwc/pcie-al.c | 373 +++++++++++++++++++++++++++
> 2 files changed, 385 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index 6ea778ae4877..3c6094cbcc3b 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -230,4 +230,16 @@ config PCIE_UNIPHIER
> Say Y here if you want PCIe controller support on UniPhier SoCs.
> This driver supports LD20 and PXs3 SoCs.
>
> +config PCIE_AL
> + bool "Amazon Annapurna Labs PCIe controller"
> + depends on OF && (ARM64 || COMPILE_TEST)
> + depends on PCI_MSI_IRQ_DOMAIN
> + select PCIE_DW_HOST
> + help
> + Say Y here to enable support of the Amazon's Annapurna Labs PCIe
> + controller IP on Amazon SoCs. The PCIe controller uses the DesignWare
> + core plus Annapurna Labs proprietary hardware wrappers. This is
> + required only for DT-based platforms. ACPI platforms with the
> + Annapurna Labs PCIe controller don't need to enable this.
> +
> endmenu
> diff --git a/drivers/pci/controller/dwc/pcie-al.c b/drivers/pci/controller/dwc/pcie-al.c
> index 3ab58f0584a8..40555532fb9a 100644
> --- a/drivers/pci/controller/dwc/pcie-al.c
> +++ b/drivers/pci/controller/dwc/pcie-al.c
> @@ -91,3 +91,376 @@ struct pci_ecam_ops al_pcie_ops = {
> };
>
> #endif /* defined(CONFIG_ACPI) && defined(CONFIG_PCI_QUIRKS) */
> +
> +#ifdef CONFIG_PCIE_AL
> +
> +#include <linux/of_pci.h>
> +#include "pcie-designware.h"
> +
> +#define AL_PCIE_REV_ID_2 2
> +#define AL_PCIE_REV_ID_3 3
> +#define AL_PCIE_REV_ID_4 4
> +
> +#define AXI_BASE_OFFSET 0x0
> +
> +#define DEVICE_ID_OFFSET 0x16c
> +
> +#define DEVICE_REV_ID 0x0
> +#define DEVICE_REV_ID_DEV_ID_MASK GENMASK(31, 16)
> +
> +#define DEVICE_REV_ID_DEV_ID_X4 0
> +#define DEVICE_REV_ID_DEV_ID_X8 2
> +#define DEVICE_REV_ID_DEV_ID_X16 4
> +
> +#define OB_CTRL_REV1_2_OFFSET 0x0040
> +#define OB_CTRL_REV3_5_OFFSET 0x0030
> +
> +#define CFG_TARGET_BUS 0x0
> +#define CFG_TARGET_BUS_MASK_MASK GENMASK(7, 0)
> +#define CFG_TARGET_BUS_BUSNUM_MASK GENMASK(15, 8)
> +
> +#define CFG_CONTROL 0x4
> +#define CFG_CONTROL_SUBBUS_MASK GENMASK(15, 8)
> +#define CFG_CONTROL_SEC_BUS_MASK GENMASK(23, 16)
> +
> +struct al_pcie_reg_offsets {
> + unsigned int ob_ctrl;
> +};
> +
> +struct al_pcie_target_bus_cfg {
> + u8 reg_val;
> + u8 reg_mask;
> + u8 ecam_mask;
> +};
> +
> +struct al_pcie {
> + struct dw_pcie *pci;
> + void __iomem *controller_base; /* base of PCIe unit (not DW core) */
> + struct device *dev;
> + resource_size_t ecam_size;
> + unsigned int controller_rev_id;
> + struct al_pcie_reg_offsets reg_offsets;
> + struct al_pcie_target_bus_cfg target_bus_cfg;
> +};
> +
> +#define PCIE_ECAM_DEVFN(x) (((x) & 0xff) << 12)
> +
> +#define to_al_pcie(x) dev_get_drvdata((x)->dev)
> +
> +static int al_pcie_rev_id_get(struct al_pcie *pcie, unsigned int *rev_id)
> +{
> + void __iomem *dev_rev_id_addr;
> + u32 dev_rev_id;
> +
> + dev_rev_id_addr = (void __iomem *)((uintptr_t)pcie->controller_base +
> + AXI_BASE_OFFSET + DEVICE_ID_OFFSET + DEVICE_REV_ID);
> +
> + dev_rev_id = FIELD_GET(DEVICE_REV_ID_DEV_ID_MASK,
> + readl(dev_rev_id_addr));
> + switch (dev_rev_id) {
> + case DEVICE_REV_ID_DEV_ID_X4:
> + *rev_id = AL_PCIE_REV_ID_2;
> + break;
> + case DEVICE_REV_ID_DEV_ID_X8:
> + *rev_id = AL_PCIE_REV_ID_3;
> + break;
> + case DEVICE_REV_ID_DEV_ID_X16:
> + *rev_id = AL_PCIE_REV_ID_4;
> + break;
> + default:
> + dev_err(pcie->dev, "Unsupported dev_rev_id (0x%x)\n",
> + dev_rev_id);
> + return -EINVAL;
> + }
> +
> + dev_dbg(pcie->dev, "dev_rev_id: 0x%x\n", dev_rev_id);
Consider s/dev_dbg/pci_dbg/g
> +
> + return 0;
> +}
> +
> +static int al_pcie_reg_offsets_set(struct al_pcie *pcie)
> +{
> + switch (pcie->controller_rev_id) {
> + case AL_PCIE_REV_ID_2:
> + pcie->reg_offsets.ob_ctrl = OB_CTRL_REV1_2_OFFSET;
> + break;
> + case AL_PCIE_REV_ID_3:
> + case AL_PCIE_REV_ID_4:
> + pcie->reg_offsets.ob_ctrl = OB_CTRL_REV3_5_OFFSET;
> + break;
> + default:
> + dev_err(pcie->dev, "Unsupported controller rev_id: 0x%x\n",
> + pcie->controller_rev_id);
Consider s/dev_err/pci_err/g
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static inline void al_pcie_target_bus_set(struct al_pcie *pcie,
> + u8 target_bus,
> + u8 mask_target_bus)
> +{
> + void __iomem *cfg_control_addr;
> + u32 reg;
> +
> + reg = FIELD_PREP(CFG_TARGET_BUS_MASK_MASK, mask_target_bus) |
> + FIELD_PREP(CFG_TARGET_BUS_BUSNUM_MASK, target_bus);
> +
> + cfg_control_addr = (void __iomem *)((uintptr_t)pcie->controller_base +
> + AXI_BASE_OFFSET + pcie->reg_offsets.ob_ctrl +
> + CFG_TARGET_BUS);
> +
> + writel(reg, cfg_control_addr);
>From what I'm seeing you commonly use writel() and readl() with a common
base address, such as pcie->controller_base + AXI_BASE_OFFSET.
I'd suggest to creating a writel and readl with that offset built-in.
> +}
> +
> +static void __iomem *al_pcie_conf_addr_map(struct al_pcie *pcie,
> + unsigned int busnr,
> + unsigned int devfn)
> +{
> + void __iomem *pci_base_addr;
Consider passing this variable declaration to the bottom, following the
reverse tree order.
> + struct pcie_port *pp = &pcie->pci->pp;
> + struct al_pcie_target_bus_cfg *target_bus_cfg = &pcie->target_bus_cfg;
> + unsigned int busnr_ecam = busnr & target_bus_cfg->ecam_mask;
> + unsigned int busnr_reg = busnr & target_bus_cfg->reg_mask;
> +
> + pci_base_addr = (void __iomem *)((uintptr_t)pp->va_cfg0_base +
> + (busnr_ecam << 20) +
> + PCIE_ECAM_DEVFN(devfn));
> +
> + if (busnr_reg != target_bus_cfg->reg_val) {
> + dev_dbg(pcie->pci->dev, "Changing target bus busnum val from 0x%x to 0x%x\n",
> + target_bus_cfg->reg_val, busnr_reg);
> + target_bus_cfg->reg_val = busnr_reg;
> + al_pcie_target_bus_set(pcie,
> + target_bus_cfg->reg_val,
> + target_bus_cfg->reg_mask);
> + }
> +
> + return pci_base_addr;
> +}
> +
> +static int al_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
> + unsigned int devfn, int where, int size,
> + u32 *val)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> + struct al_pcie *pcie = to_al_pcie(pci);
> + unsigned int busnr = bus->number;
> + void __iomem *pci_addr;
> + int rc;
> +
> + pci_addr = al_pcie_conf_addr_map(pcie, busnr, devfn);
> +
> + rc = dw_pcie_read(pci_addr + where, size, val);
> +
> + dev_dbg(pci->dev, "%d-byte config read from %04x:%02x:%02x.%d offset 0x%x (pci_addr: 0x%px) - val:0x%x\n",
> + size, pci_domain_nr(bus), bus->number,
> + PCI_SLOT(devfn), PCI_FUNC(devfn), where,
> + (pci_addr + where), *val);
> +
> + return rc;
> +}
> +
> +static int al_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
> + unsigned int devfn, int where, int size,
> + u32 val)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> + struct al_pcie *pcie = to_al_pcie(pci);
> + unsigned int busnr = bus->number;
> + void __iomem *pci_addr;
> + int rc;
> +
> + pci_addr = al_pcie_conf_addr_map(pcie, busnr, devfn);
> +
> + rc = dw_pcie_write(pci_addr + where, size, val);
> +
> + dev_err(pci->dev, "%d-byte config write to %04x:%02x:%02x.%d offset 0x%x (pci_addr: 0x%px) - val:0x%x\n",
> + size, pci_domain_nr(bus), bus->number,
> + PCI_SLOT(devfn), PCI_FUNC(devfn), where,
> + (pci_addr + where), val);
> +
> + return rc;
> +}
> +
> +static int al_pcie_config_prepare(struct al_pcie *pcie)
> +{
> + struct al_pcie_target_bus_cfg *target_bus_cfg;
> + struct pcie_port *pp = &pcie->pci->pp;
> + unsigned int ecam_bus_mask;
> + u8 secondary_bus;
> + u8 subordinate_bus;
> + void __iomem *cfg_control_addr;
> + u32 cfg_control;
> + u32 reg;
> +
> + target_bus_cfg = &pcie->target_bus_cfg;
> +
> + ecam_bus_mask = (pcie->ecam_size >> 20) - 1;
> + if (ecam_bus_mask > 255) {
> + dev_warn(pcie->dev, "ECAM window size is larger than 256MB. Cutting off at 256\n");
> + ecam_bus_mask = 255;
> + }
> +
> + /* This portion is taken from the transaction address */
> + target_bus_cfg->ecam_mask = ecam_bus_mask;
> + /* This portion is taken from the cfg_target_bus reg */
> + target_bus_cfg->reg_mask = ~target_bus_cfg->ecam_mask;
> + target_bus_cfg->reg_val = pp->busn->start & target_bus_cfg->reg_mask;
> +
> + al_pcie_target_bus_set(pcie, target_bus_cfg->reg_val,
> + target_bus_cfg->reg_mask);
> +
> + secondary_bus = pp->busn->start + 1;
> + subordinate_bus = pp->busn->end;
> +
> + /* Set the valid values of secondary and subordinate buses */
> + cfg_control_addr = pcie->controller_base + AXI_BASE_OFFSET +
> + pcie->reg_offsets.ob_ctrl + CFG_CONTROL;
> +
> + cfg_control = readl(cfg_control_addr);
> +
> + reg = cfg_control &
> + ~(CFG_CONTROL_SEC_BUS_MASK | CFG_CONTROL_SUBBUS_MASK);
> +
> + reg |= FIELD_PREP(CFG_CONTROL_SUBBUS_MASK, subordinate_bus) |
> + FIELD_PREP(CFG_CONTROL_SEC_BUS_MASK, secondary_bus);
> +
> + writel(reg, cfg_control_addr);
> +
> + return 0;
> +}
> +
> +static int al_pcie_host_init(struct pcie_port *pp)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> + struct al_pcie *pcie = to_al_pcie(pci);
> + int link_up;
> + int rc;
> +
> + link_up = dw_pcie_link_up(pci);
> + if (!link_up) {
> + dev_err(pci->dev, "link is not up!\n");
> + return -ENOLINK;
> + }
> +
> + dev_info(pci->dev, "link is up\n");
Consider s/dev_info/pci_info/g
> +
> + rc = al_pcie_rev_id_get(pcie, &pcie->controller_rev_id);
> + if (rc)
> + return rc;
> +
> + rc = al_pcie_reg_offsets_set(pcie);
> + if (rc)
> + return rc;
> +
> + rc = al_pcie_config_prepare(pcie);
> + if (rc)
> + return rc;
> +
> + return 0;
> +}
> +
> +static const struct dw_pcie_host_ops al_pcie_host_ops = {
> + .rd_other_conf = al_pcie_rd_other_conf,
> + .wr_other_conf = al_pcie_wr_other_conf,
> + .host_init = al_pcie_host_init,
> +};
> +
> +static int al_add_pcie_port(struct pcie_port *pp,
> + struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + int ret;
> +
> + pp->ops = &al_pcie_host_ops;
> +
> + ret = dw_pcie_host_init(pp);
> + if (ret) {
> + dev_err(dev, "failed to initialize host\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct dw_pcie_ops dw_pcie_ops = {
> +};
> +
> +static int al_pcie_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct al_pcie *al_pcie;
> + struct dw_pcie *pci;
> + struct resource *dbi_res;
> + struct resource *controller_res;
> + struct resource *ecam_res;
> + int ret;
Please sort the variables following the reverse tree order.
> +
> + al_pcie = devm_kzalloc(dev, sizeof(*al_pcie), GFP_KERNEL);
> + if (!al_pcie)
> + return -ENOMEM;
> +
> + pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL);
> + if (!pci)
> + return -ENOMEM;
> +
> + pci->dev = dev;
> + pci->ops = &dw_pcie_ops;
> +
> + al_pcie->pci = pci;
> + al_pcie->dev = dev;
> +
> + dbi_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
> + pci->dbi_base = devm_pci_remap_cfg_resource(dev, dbi_res);
> + if (IS_ERR(pci->dbi_base)) {
> + dev_err(dev, "couldn't remap dbi base %pR\n", dbi_res);
> + return PTR_ERR(pci->dbi_base);
> + }
> +
> + ecam_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
> + if (!ecam_res) {
> + dev_err(dev, "couldn't find 'config' reg in DT\n");
> + return -ENOENT;
> + }
> + al_pcie->ecam_size = resource_size(ecam_res);
> +
> + controller_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> + "controller");
> + al_pcie->controller_base = devm_ioremap_resource(dev, controller_res);
> + if (IS_ERR(al_pcie->controller_base)) {
> + dev_err(dev, "couldn't remap controller base %pR\n",
> + controller_res);
> + return PTR_ERR(al_pcie->controller_base);
> + }
> +
> + dev_dbg(dev, "From DT: dbi_base: %pR, controller_base: %pR\n",
> + dbi_res, controller_res);
> +
> + platform_set_drvdata(pdev, al_pcie);
> +
> + ret = al_add_pcie_port(&pci->pp, pdev);
> + if (ret)
> + return ret;
> +
> + return 0;
Those operations are redundant, aren't they? They can be replaced just
by:
return ret;
> +}
> +
> +static const struct of_device_id al_pcie_of_match[] = {
> + { .compatible = "amazon,al-pcie",
> + },
> + {},
> +};
> +
> +static struct platform_driver al_pcie_driver = {
> + .driver = {
> + .name = "al-pcie",
> + .of_match_table = al_pcie_of_match,
> + .suppress_bind_attrs = true,
> + },
> + .probe = al_pcie_probe,
> +};
> +builtin_platform_driver(al_pcie_driver);
> +
> +#endif /* CONFIG_PCIE_AL*/
> --
> 2.17.1
