On Wed, Jul 17, 2019 at 4:05 AM Biwen Li <biwen.li@xxxxxxx> wrote:
>
> >
> > Caution: EXT Email
> >
> > On Tue, Jul 16, 2019 at 4:26 AM Biwen Li <biwen.li@xxxxxxx> wrote:
> > >
> > > The patch adds binding for ftm alarm driver
> >
> > Bindings are for h/w, not drivers...
> >
> > 'dt-bindings: rtc: ...' for the subject prefix.
> I will correct it in v6.
> >
> > >
> > > Signed-off-by: Biwen Li <biwen.li@xxxxxxx>
> > > ---
> > > Change in v5:
> > > - None
> > >
> > > Change in v4:
> > > - add note about dts and kernel options
> > > - add aliases in example
> > >
> > > Change in v3:
> > > - remove reg-names property
> > > - correct cells number
> > >
> > > Change in v2:
> > > - replace ls1043a with ls1088a as example
> > > - add rcpm node and fsl,rcpm-wakeup property
> > >
> > >
> > > .../bindings/rtc/rtc-fsl-ftm-alarm.txt | 49 +++++++++++++++++++
> > > 1 file changed, 49 insertions(+)
> > > create mode 100644
> > > Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt
> > > b/Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt
> > > new file mode 100644
> > > index 000000000000..fb018065406c
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt
> > > @@ -0,0 +1,49 @@
> > > +Freescale FlexTimer Module (FTM) Alarm
> > > +
> > > +Note:
> > > +- The driver depends on RCPM driver
> > > + to wake up system in sleep.
> > > +- Need stop using RTC_HCTOSYS or use the DT aliases
> > > + to ensure the driver is not used as the primary RTC.
> > > + (Select DT aliases defaultly)
> >
> > This is Linux specific and not relevant to the binding.
> Ok, I will remove all of the Note in v6.
> >
> > > +
> > > +Required properties:
> > > +- compatible : Should be "fsl,<chip>-ftm-alarm", the
> > > + supported chips include
> > > + "fsl,ls1012a-ftm-alarm"
> > > + "fsl,ls1021a-ftm-alarm"
> > > + "fsl,ls1028a-ftm-alarm"
> > > + "fsl,ls1043a-ftm-alarm"
> > > + "fsl,ls1046a-ftm-alarm"
> > > + "fsl,ls1088a-ftm-alarm"
> > > + "fsl,ls208xa-ftm-alarm"
> > > +- reg : Specifies base physical address and size of the register sets
> > > +for the
> > > + FlexTimer Module and base physical address of IP Powerdown
> > > +Exception Control
> > > + Register.
> > > +- interrupts : Should be the FlexTimer Module interrupt.
> > > +- fsl,rcpm-wakeup property and rcpm node : Please refer
> > > + Documentation/devicetree/bindings/soc/fsl/rcpm.txt
> > > +
> > > +Optional properties:
> > > +- big-endian: If the host controller is big-endian mode, specify this property.
> > > + The default endian mode is little-endian.
> > > +
> > > +Example:
> > > +aliases {
> > > + ...
> > > + rtc1 = ftm_alarm0; /* Use flextimer alarm driver as /dev/rtc1 */
> > > + ...
> > > +};
> >
> > Drop the aliases part. It's not going to work when this is converted to DT schema
> > and the comment is Linux specific.
> Sorry,I can't drop the aliases part. If any user uses the alarm driver as rtc0,
> the user will get wrong time from /dev/rtc0.It is very important.
I just mean don't put it in the example. You can use it in your dts file.
