Hi Krzysztof,
On 12.07.19 16:12, Krzysztof Kozlowski wrote:
> Add support for iMX6-UL2 modules from Kontron Electronics GmbH (before
> acquisition: Exceet Electronics) and evalkit boards based on it:
>
> 1. i.MX6 UL System-on-Module, a 25x25 mm solderable module (LGA pads and
> pin castellations) with 256 MB RAM, 1 MB NOR-Flash, 256 MB NAND and
> other interfaces,
> 1. UL2 evalkit, w/wo eMMC, without display,
> 2. UL2 evalkit with 4.3" display,
> 3. UL2 evalkit with 5.0" display.
We will use a new naming scheme for these and other boards. The new
names would be:
1. Kontron N6310 SOM (i.MX6UL SoM with 256MB RAM/NAND)
2. Kontron N6310 S (Evalkit with SoM)
3. Kontron N6310 S 43 (Evalkit with SoM and 4.3" display)
4. Kontron N6310 S 50 (Evalkit with SoM and 5.0" display)
>
> This includes device nodes for unsupported displays (Admatec
> T043C004800272T2A and T070P133T0S301).
>
> The work is based on Exceet source code (GPLv2) with numerous changes:
> 1. Reorganize files,
> 2. Rename Exceet -> Kontron,
> 3. Fix coding style errors,
> 4. Fix DTC warnings,
> 5. Extend compatibles so eval boards inherit the SoM compatible,
> 6. Use defines instead of GPIO flag values,
> 7. Adjust operating points of CPU0,
> 8. Sort nodes alphabetically.
>
> In downstream BSP the Exceet name still appears in multiple places
> therefore I left it in the model names.
Actually "exceet" can be dropped everywhere, except for the copyrights
in the file headers.
>
> Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> ---
> arch/arm/boot/dts/Makefile | 3 +
> arch/arm/boot/dts/imx6ul-kontron-ul2-43.dts | 123 +++++
> arch/arm/boot/dts/imx6ul-kontron-ul2-50.dts | 123 +++++
> arch/arm/boot/dts/imx6ul-kontron-ul2-som.dtsi | 152 ++++++
> arch/arm/boot/dts/imx6ul-kontron-ul2.dts | 435 ++++++++++++++++++
> 5 files changed, 836 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6ul-kontron-ul2-43.dts
> create mode 100644 arch/arm/boot/dts/imx6ul-kontron-ul2-50.dts
> create mode 100644 arch/arm/boot/dts/imx6ul-kontron-ul2-som.dtsi
> create mode 100644 arch/arm/boot/dts/imx6ul-kontron-ul2.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9159fa2cea90..3431bb44fb5d 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -569,6 +569,9 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
> imx6ul-geam.dtb \
> imx6ul-isiot-emmc.dtb \
> imx6ul-isiot-nand.dtb \
> + imx6ul-kontron-ul2.dtb \
> + imx6ul-kontron-ul2-43.dtb \
> + imx6ul-kontron-ul2-50.dtb \
The preferred names for these files would be:
imx6ul-kontron-n6310-s.dtb
imx6ul-kontron-n6310-s-43.dtb
imx6ul-kontron-n6310-s-50.dtb
> imx6ul-liteboard.dtb \
> imx6ul-opos6uldev.dtb \
> imx6ul-pico-hobbit.dtb \
> diff --git a/arch/arm/boot/dts/imx6ul-kontron-ul2-43.dts b/arch/arm/boot/dts/imx6ul-kontron-ul2-43.dts
> new file mode 100644
> index 000000000000..a2b68ba14765
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-kontron-ul2-43.dts
> @@ -0,0 +1,123 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2017 exceet electronics GmbH
Could you add another line here, to reflect the acquisition?
Copyright (C) 2018 Kontron Electronics GmbH
> + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
You can drop this license text in favor of the SPDX tag.
> + */
> +
> +#include "imx6ul-kontron-ul2.dts"
> +
> +/ {
> + model = "Exceet/Kontron iMX6 UL-2 S 43";
Please use:
model = "Kontron N6310 S 43";
> + compatible = "kontron,imx6ul-ul2-s-43", "kontron,imx6ul-ul2-s",
> + "kontron,imx6ul-ul2-som", "fsl,imx6ul";
And here:
compatible = "kontron,n6310-s-43", "kontron,n6310-s",
"kontron,n6310-som", "fsl,imx6ul";
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm7 0 5000000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + status = "okay";
> + };
> +
> + panel {
> + compatible = "admatec,t043c004800272t2a";
> + backlight = <&backlight>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&display_out>;
> + };
> + };
> + };
> +};
> +
> +&i2c4 {
> + gt911@5d {
> + compatible = "goodix,gt928";
> + reg = <0x5d>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_cap_touch>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <6 8>;
> + reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
> + irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl_lcdif_dat: lcdifdatgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
> + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
> + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
> + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
> + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
> + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
> + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
> + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
> + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
> + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
> + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
> + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
> + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
> + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
> + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
> + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
> + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
> + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
> + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
> + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
> + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
> + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
> + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
> + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
> + >;
> + };
> +
> + pinctrl_lcdif_ctrl: lcdifctrlgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
> + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
> + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
> + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
> + MX6UL_PAD_LCD_RESET__LCDIF_RESET 0x79
> + >;
> + };
> +
> + pinctrl_cap_touch: captouchgrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* Touch Interrupt */
> + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* Touch Reset */
> + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Touch Wake */
> + >;
> + };
> +
> + pinctrl_pwm7: pwm7grp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_VSYNC__PWM7_OUT 0x110b0
> + >;
> + };
> +};
> +
> +&lcdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcdif_dat
> + &pinctrl_lcdif_ctrl>;
> + status = "okay";
> +
> + port {
> + display_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> +};
> +
> +&pwm7 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm7>;
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-kontron-ul2-50.dts b/arch/arm/boot/dts/imx6ul-kontron-ul2-50.dts
> new file mode 100644
> index 000000000000..61017020e02f
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-kontron-ul2-50.dts
> @@ -0,0 +1,123 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2017 exceet electronics GmbH
See above.
> + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
See above.
> + */
> +
> +#include "imx6ul-kontron-ul2.dts"
> +
> +/ {
> + model = "Exceet/Kontron iMX6 UL-2 S 50";
> + compatible = "kontron,imx6ul-ul2-s-50", "kontron,imx6ul-ul2-s",
> + "kontron,imx6ul-ul2-som", "fsl,imx6ul";
See above (drop exceet, "iMX6 UL-2 S 50" -> "N6310 S 50", "imx6ul-ul2"
-> "n6310").
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm7 0 5000000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + status = "okay";
> + };
> +
> + panel {
> + compatible = "admatec,t070p133t0s301";
> + backlight = <&backlight>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&display_out>;
> + };
> + };
> + };
> +};
> +
> +&i2c4 {
> + gt911@5d {
> + compatible = "goodix,gt928";
> + reg = <0x5d>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_cap_touch>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <6 8>;
> + reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
> + irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl_lcdif_dat: lcdifdatgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
> + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
> + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
> + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
> + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
> + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
> + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
> + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
> + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
> + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
> + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
> + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
> + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
> + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
> + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
> + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
> + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
> + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
> + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
> + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
> + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
> + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
> + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
> + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
> + >;
> + };
> +
> + pinctrl_lcdif_ctrl: lcdifctrlgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
> + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
> + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
> + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
> + MX6UL_PAD_LCD_RESET__LCDIF_RESET 0x79
> + >;
> + };
> +
> + pinctrl_cap_touch: captouchgrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* Touch Interrupt */
> + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* Touch Reset */
> + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Touch Wake */
> + >;
> + };
> +
> + pinctrl_pwm7: pwm7grp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_VSYNC__PWM7_OUT 0x110b0
> + >;
> + };
> +};
> +
> +&lcdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcdif_dat
> + &pinctrl_lcdif_ctrl>;
> + status = "okay";
> +
> + port {
> + display_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> +};
> +
> +&pwm7 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm7>;
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-kontron-ul2-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-ul2-som.dtsi
> new file mode 100644
> index 000000000000..26b6615cf839
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-kontron-ul2-som.dtsi
The preferred name for this file would be:
imx6ul-kontron-n6310-som.dtb
> @@ -0,0 +1,152 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2017 exceet electronics GmbH
See above.
> + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
See above.
> + */
> +
> +#include "imx6ul.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Exceet/Kontron iMX6 UL-2 SOM";
> + compatible = "kontron,imx6ul-ul2-som", "fsl,imx6ul";
See above (drop exceet, "iMX6 UL-2 SOM" -> "N6310 SOM", "imx6ul-ul2-som"
-> "n6310-som").
> +
> + memory@80000000 {
> + reg = <0x80000000 0x10000000>;
> + };
> +};
> +
> +&cpu0 {
> + clock-frequency = <528000000>;
> + operating-points = <
> + /* kHz uV */
> + 528000 1175000
> + 396000 1025000
> + 198000 950000
> + >;
> + fsl,soc-operating-points = <
> + /* KHz uV */
> + 528000 1175000
> + 396000 1175000
> + 198000 1175000
> + >;
> +};
What's the reason behind overwriting the operating-points and setting
clock-frequency? Doesn't imx6q-cpufreq.c already read the speed grades
from the hardware and adjust the operating-points accordingly?
> +
> +&ecspi2 {
> + cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + status = "okay";
> +
> + flash: mx25v80@0 {
> + compatible = "macronix,mx25v8035f", "jedec,spi-nor";
> + spi-max-frequency = <50000000>;
> + reg = <0>;
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
> + phy-mode = "rmii";
> + phy-handle = <ðphy1>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@1 {
> + reg = <1>;
> + micrel,led-mode = <0>;
> + clocks = <&clks IMX6UL_CLK_ENET_REF>;
> + clock-names = "rmii-ref";
> + };
> + };
> +};
> +
> +&fec2 {
> + phy-mode = "rmii";
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reset_out>;
> +
> + pinctrl_reset_out: rstoutgrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1
> + MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1
> + MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1
> + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1
> + >;
> + };
> +
> + pinctrl_enet1: enet1grp {
> + fsl,pins = <
> + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
> + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
> + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
> + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
> + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
> + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
> + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
> + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009
> + >;
> + };
> +
> + pinctrl_enet1_mdio: enet1mdiogrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
> + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
> + >;
> + };
> +
> + pinctrl_qspi: qspigrp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
> + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
> + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
> + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
> + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
> + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
> + >;
> + };
> +};
> +
> +&qspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_qspi>;
> + status = "okay";
> +
> + flash0: w25m02gv@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "spi-nand";
> + spi-max-frequency = <108000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + reg = <0>;
> +
> + partition@0 {
> + label = "ubi1";
> + reg = <0x00000000 0x08000000>;
> + };
> +
> + partition@8000000 {
> + label = "ubi2";
> + reg = <0x08000000 0x08000000>;
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-kontron-ul2.dts b/arch/arm/boot/dts/imx6ul-kontron-ul2.dts
> new file mode 100644
> index 000000000000..6d394a97712b
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-kontron-ul2.dts
> @@ -0,0 +1,435 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2017 exceet electronics GmbH
See above.
> + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
See above.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6ul-kontron-ul2-som.dtsi"
> +
> +/ {
> + model = "Exceet/Kontron iMX6 UL-2 S";
> + compatible = "kontron,imx6ul-ul2-s", "kontron,imx6ul-ul2-som",
> + "fsl,imx6ul";
See above (drop exceet, "iMX6 UL-2 S" -> "N6310 S", "imx6ul-ul2" ->
"n6310").
> +
> + pwm-beeper {
> + compatible = "pwm-beeper";
> + pwms = <&pwm8 0 5000>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> + led1 {
> + label = "debug-led1";
> + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led2 {
> + label = "debug-led2";
> + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + };
> +
> + led3 {
> + label = "debug-led3";
> + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
We copied this from some other devicetree and I'm not sure in what case
we should really group the regulators in a simple-bus, or what's the
reason behind this. But others do it like this, so it's probably not so
wrong.
Thanks,
Frieder
> +
> + reg_3v3: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + reg_vref_adc: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "vref-adc";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + reg_usb_otg1_vbus: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "usb_otg1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> + };
> +
> +};
> +
> +&adc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc1>;
> + num-channels = <3>;
> + vref-supply = <®_vref_adc>;
> + status = "okay";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + status = "okay";
> +};
> +
> +&ecspi1 {
> + fsl,spi-num-chipselects = <1>;
> + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + status = "okay";
> +
> + fram@0 {
> + compatible = "atmel,at25";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + spi-cpha;
> + spi-cpol;
> + pagesize = <1>;
> + size = <8192>;
> + address-width = <16>;
> + };
> +};
> +
> +&fec1 {
> + pinctrl-0 = <&pinctrl_enet1>;
> + /delete-node/ mdio;
> +};
> +
> +&fec2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
> + phy-mode = "rmii";
> + phy-handle = <ðphy2>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@1 {
> + reg = <1>;
> + micrel,led-mode = <0>;
> + clocks = <&clks IMX6UL_CLK_ENET_REF>;
> + clock-names = "rmii-ref";
> + };
> +
> + ethphy2: ethernet-phy@2 {
> + reg = <2>;
> + micrel,led-mode = <0>;
> + clocks = <&clks IMX6UL_CLK_ENET2_REF>;
> + clock-names = "rmii-ref";
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +};
> +
> +&i2c4 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + status = "okay";
> +
> + rtc@32 {
> + compatible = "epson,rx8900";
> + reg = <0x32>;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0
> + >;
> + };
> +
> + pinctrl_gpio: gpio {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */
> + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */
> + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */
> + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */
> + >;
> + };
> +
> + pinctrl_usbotg1: usbotg1 {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0
> + >;
> + };
> +
> + pinctrl_gpio_leds: gpio_leds {
> + fsl,pins = <
> + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */
> + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */
> + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */
> + >;
> + };
> +
> + /* FRAM */
> + pinctrl_ecspi1: ecspi1grp-1 {
> + fsl,pins = <
> + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1
> + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1
> + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1
> + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */
> + >;
> + };
> +
> + pinctrl_enet2: enet2grp {
> + fsl,pins = <
> + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
> + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
> + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
> + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
> + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
> + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
> + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
> + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009
> + >;
> + };
> +
> + pinctrl_enet2_mdio: enet2mdiogrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
> + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
> + >;
> + };
> +
> + pinctrl_flexcan2: flexcan2grp{
> + fsl,pins = <
> + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
> + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
> + >;
> + };
> +
> + pinctrl_pwm8: pwm8grp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
> + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1
> + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1
> + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1
> + /*
> + * mux unused RTS to make sure it doesn't cause
> + * any interrupts when it is undefined
> + */
> + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
> + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
> + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
> + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
> + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
> + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
> + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
> + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
> + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
> + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
> + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059
> + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
> + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
> + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
> + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
> + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
> + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
> + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
> + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
> + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
> + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
> + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
> + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
> + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
> + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
> + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
> + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0
> + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0
> + >;
> + };
> +
> + pinctrl_adc1: adc1grp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
> + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
> + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0
> + >;
> + };
> +};
> +
> +&pwm8 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm8>;
> + status = "okay";
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + linux,rs485-enabled-at-boot-time;
> + rs485-rx-during-tx;
> + rs485-rts-active-low;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg1>;
> + dr_mode = "otg";
> + status = "okay";
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + vbus-supply = <®_usb_otg1_vbus>;
> +};
> +
> +&usbotg2 {
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
> + keep-power-in-suspend;
> + enable-sdio-wakeup;
> + vmmc-supply = <®_3v3>;
> + voltage-ranges = <3300 3300>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + tuning-step = <2>;
> + non-removable;
> + keep-power-in-suspend;
> + enable-sdio-wakeup;
> + vmmc-supply = <®_3v3>;
> + voltage-ranges = <3300 3300>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + status = "okay";
> + fsl,ext-reset-output;
> +};
>
