Re: [PATCH v1 03/11] dt-bindings: display/bridge: Add config property for ti948

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Laurent,

On 11/06/2019 19:07, Laurent Pinchart wrote:
> Hi Michael,
> 
> Thank you for the patch.

My pleasure, and thank you for the feedback!

> On Tue, Jun 11, 2019 at 03:04:04PM +0100, Michael Drake wrote:
>> The config property can be used to provide an array of
>> register addresses and values to be written to configure
>> the device for the board.
> 
> Please don't. DT describes the hardware (or more accurately the system),
> it's not meant to store arbitrary configuration data. All the registers
> specified below should instead be set by the driver based on a
> combination of hardware description and information obtained at runtime.

OK, understood.  I'll work on this.  For some of them
explicit firmware properties would be appropriate.

I'll go through it to ascertain what can be determined
at runtime.

>> Signed-off-by: Michael Drake <michael.drake@xxxxxxxxxxxxxxx>
>> Cc: Patrick Glaser <pglaser@xxxxxxxxx>
>> Cc: Nate Case <ncase@xxxxxxxxx>
>> ---
>>  .../bindings/display/bridge/ti,ds90ub948.txt  | 21 +++++++++++++++++++
>>  1 file changed, 21 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/display/bridge/ti,ds90ub948.txt b/Documentation/devicetree/bindings/display/bridge/ti,ds90ub948.txt
>> index f9e86cb22900..1e7033b0f3b7 100644
>> --- a/Documentation/devicetree/bindings/display/bridge/ti,ds90ub948.txt
>> +++ b/Documentation/devicetree/bindings/display/bridge/ti,ds90ub948.txt
>> @@ -12,6 +12,8 @@ Required properties:
>>  Optional properties:
>>  
>>  - regulators: List of regulator name strings to enable for operation of device.
>> +- config: List of <register address>,<value> pairs to be set to configure
>> +  device on powerup.  The register addresses and values are 8bit.
>>  
>>  Example
>>  -------
>> @@ -21,4 +23,23 @@ ti948: ds90ub948@0 {
>>  
>>  	regulators: "vcc",
>>  	            "vcc_disp";
>> +	config:
>> +	        /* set error count to max */
>> +	        <0x41>, <0x1f>,
>> +	        /* sets output mode, no change noticed */
>> +	        <0x49>, <0xe0>,
>> +	        /* speed up I2C, 0xE is around 480KHz */
>> +	        <0x26>, <0x0e>,
>> +	        /* speed up I2C, 0xE is around 480KHz */
>> +	        <0x27>, <0x0e>,
>> +	        /* sets GPIO0 as an input */
>> +	        <0x1D>, <0x13>,
>> +	        /* set GPIO2 high, backlight PWM (set to 0x50 for normal use) */
>> +	        <0x1E>, <0x50>,
>> +	        /* sets GPIO3 as an output with remote control for touch XRES */
>> +	        <0x1F>, <0x05>,
>> +	        /* set GPIO5 high, backlight enable on new display */
>> +	        <0x20>, <0x09>,
>> +	        /* set GPIO7 and GPIO8 high to enable touch power and prox sense */
>> +	        <0x21>, <0x91>;
>>  };
> 

-- 
Michael Drake                 https://www.codethink.co.uk/



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux