Configure the RTL8211E LEDs behavior when the device tree property
'realtek,led-modes' is specified.
Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
---
TODO: DT validation
Changes in v3:
- sanity check led-modes values
- set LACR bits in a more readable way
- use phydev_err() instead of dev_err()
- log an error if LED configuration fails
Changes in v2:
- patch added to the series
---
drivers/net/phy/realtek.c | 72 +++++++++++++++++++++++++++++++++++++--
1 file changed, 70 insertions(+), 2 deletions(-)
diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
index 5854412403b5..e9fb67654c4e 100644
--- a/drivers/net/phy/realtek.c
+++ b/drivers/net/phy/realtek.c
@@ -9,10 +9,12 @@
* Copyright (c) 2004 Freescale Semiconductor, Inc.
*/
#include <linux/bitops.h>
+#include <linux/bits.h>
#include <linux/device.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/phy.h>
+#include <dt-bindings/net/realtek.h>
#define RTL821x_PHYSR 0x11
#define RTL821x_PHYSR_DUPLEX BIT(13)
@@ -34,6 +36,15 @@
#define RTL8211E_EEE_LED_MODE1 0x05
#define RTL8211E_EEE_LED_MODE2 0x06
+/* RTL8211E extension page 44 */
+#define RTL8211E_LACR 0x1a
+#define RLT8211E_LACR_LEDACTCTRL_SHIFT 4
+#define RLT8211E_LACR_LEDACTCTRL_MASK GENMASK(6, 4)
+#define RTL8211E_LCR 0x1c
+#define RTL8211E_LCR_LEDCTRL_MASK (GENMASK(2, 0) | \
+ GENMASK(6, 4) | \
+ GENMASK(10, 8))
+
/* RTL8211E extension page 160 */
#define RTL8211E_SCR 0x1a
#define RTL8211E_SCR_DISABLE_RXC_SSC BIT(2)
@@ -123,6 +134,62 @@ static void rtl8211e_disable_eee_led_mode(struct phy_device *phydev)
phy_restore_page(phydev, oldpage, err);
}
+static int rtl8211e_config_leds(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int count, i, oldpage, ret;
+ u16 lacr_bits = 0, lcr_bits = 0;
+
+ if (!dev->of_node)
+ return 0;
+
+ if (of_property_read_bool(dev->of_node, "realtek,eee-led-mode-disable"))
+ rtl8211e_disable_eee_led_mode(phydev);
+
+ count = of_property_count_elems_of_size(dev->of_node,
+ "realtek,led-modes",
+ sizeof(u32));
+ if (count < 0 || count > 3)
+ return -EINVAL;
+
+ for (i = 0; i < count; i++) {
+ u32 val;
+
+ of_property_read_u32_index(dev->of_node,
+ "realtek,led-modes", i, &val);
+ if ((val > RTL8211E_LINK_10_100_1000 &&
+ val < RTL8211E_LINK_ACTIVITY) ||
+ val > (RTL8211E_LINK_ACTIVITY | RTL8211E_LINK_10_100_1000))
+ return -EINVAL;
+
+ if (val & RTL8211E_LINK_ACTIVITY)
+ lacr_bits |= BIT(RLT8211E_LACR_LEDACTCTRL_SHIFT + i);
+
+ lcr_bits |= (u16)(val & 0xf) << (i * 4);
+ }
+
+ oldpage = rtl8211e_select_ext_page(phydev, 44);
+ if (oldpage < 0) {
+ phydev_err(phydev, "failed to select extended page: %d\n", oldpage);
+ goto err;
+ }
+
+ ret = __phy_modify(phydev, RTL8211E_LACR,
+ RLT8211E_LACR_LEDACTCTRL_MASK, lacr_bits);
+ if (ret) {
+ phydev_err(phydev, "failed to write LACR reg: %d\n", ret);
+ goto err;
+ }
+
+ ret = __phy_modify(phydev, RTL8211E_LCR,
+ RTL8211E_LCR_LEDCTRL_MASK, lcr_bits);
+ if (ret)
+ phydev_err(phydev, "failed to write LCR reg: %d\n", ret);
+
+err:
+ return phy_restore_page(phydev, oldpage, ret);
+}
+
static int rtl8201_ack_interrupt(struct phy_device *phydev)
{
int err;
@@ -267,8 +334,9 @@ static int rtl8211e_config_init(struct phy_device *phydev)
ret);
}
- if (of_property_read_bool(dev->of_node, "realtek,eee-led-mode-disable"))
- rtl8211e_disable_eee_led_mode(phydev);
+ ret = rtl8211e_config_leds(phydev);
+ if (ret)
+ phydev_err(phydev, "LED configuration failed: %d\n", ret);
/* enable TX/RX delay for rgmii-* modes, and disable them for rgmii. */
switch (phydev->interface) {
--
2.22.0.410.gd8fdbe21b5-goog
