Hi,
On Wed, Jul 03, 2019 at 10:09:39PM +0200, Heiner Kallweit wrote:
> On 03.07.2019 21:37, Matthias Kaehlcke wrote:
> > EEE LED mode is enabled by default on the RTL8211E. Disable it when
> > the device tree property 'realtek,eee-led-mode-disable' exists.
> >
> > The magic values to disable EEE LED mode were taken from the RTL8211E
> > datasheet, unfortunately they are not further documented.
> >
> > Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
> > ---
> > Changes in v2:
> > - patch added to the series
> > ---
> > drivers/net/phy/realtek.c | 37 ++++++++++++++++++++++++++++++++++++-
> > 1 file changed, 36 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> > index a669945eb829..eb815cbe1e72 100644
> > --- a/drivers/net/phy/realtek.c
> > +++ b/drivers/net/phy/realtek.c
> > @@ -9,8 +9,9 @@
> > * Copyright (c) 2004 Freescale Semiconductor, Inc.
> > */
> > #include <linux/bitops.h>
> > -#include <linux/phy.h>
> > #include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/phy.h>
> >
> > #define RTL821x_PHYSR 0x11
> > #define RTL821x_PHYSR_DUPLEX BIT(13)
> > @@ -26,6 +27,10 @@
> > #define RTL821x_EXT_PAGE_SELECT 0x1e
> > #define RTL821x_PAGE_SELECT 0x1f
> >
> > +/* RTL8211E page 5 */
> > +#define RTL8211E_EEE_LED_MODE1 0x05
> > +#define RTL8211E_EEE_LED_MODE2 0x06
> > +
> > #define RTL8211F_INSR 0x1d
> >
> > #define RTL8211F_TX_DELAY BIT(8)
> > @@ -53,6 +58,35 @@ static int rtl821x_write_page(struct phy_device *phydev, int page)
> > return __phy_write(phydev, RTL821x_PAGE_SELECT, page);
> > }
> >
> > +static int rtl8211e_disable_eee_led_mode(struct phy_device *phydev)
> > +{
>
> You define return type int but AFAICS the return value is never used,
> also in subsequent patches.
ok, I'll change it to void
> > + int ret = 0;
> > + int oldpage;
> > +
> > + oldpage = phy_select_page(phydev, 5);
> > + if (oldpage < 0)
> > + goto out;
> > +
> > + /* write magic values to disable EEE LED mode */
> > + ret = __phy_write(phydev, RTL8211E_EEE_LED_MODE1, 0x8b82);
> > + if (ret)
> > + goto out;
> > +
> > + ret = __phy_write(phydev, RTL8211E_EEE_LED_MODE2, 0x052b);
> > +
> > +out:
> > + return phy_restore_page(phydev, oldpage, ret);
> > +}
> > +
> > +static int rtl8211e_config_init(struct phy_device *phydev)
> > +{
> > + struct device *dev = &phydev->mdio.dev;
> > +
> > + if (of_property_read_bool(dev->of_node, "realtek,eee-led-mode-disable"))
> > + rtl8211e_disable_eee_led_mode(phydev);
> > +
> > + return 0;
> > +}
>
> I suppose checkpatch complains about the missing empty line.
> You add it in a later patch, in case of a v3 you could fix that.
Actually checkpatch does not complain, I'll fix it in v3.
Thanks
Matthias
