[PATCH 1/2] device-tree: iio: add bindings documentation for NXP PCT2075

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This documentens the bindings for the NXP PCT2075 temperature sensor
driver.

Signed-off-by: Daniel Mack <daniel@xxxxxxxxxx>
---
 .../bindings/iio/temperature/pct2075.txt      | 60 +++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/temperature/pct2075.txt

diff --git a/Documentation/devicetree/bindings/iio/temperature/pct2075.txt b/Documentation/devicetree/bindings/iio/temperature/pct2075.txt
new file mode 100644
index 000000000000..dc5d3e991ab0
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/pct2075.txt
@@ -0,0 +1,60 @@
+* NXP PCT2075 - I2C connected digital temperature sensor
+
+Link to datasheet: https://www.nxp.com/docs/en/data-sheet/PCT2075.pdf
+
+Required properties:
+
+ - compatible:	Should be "nxp,pct2075"
+ - reg:		The I2C address of the sensor
+		(controllable via A[0,1,2] pins)
+
+Addressing pins can be tied high, low or left floating, allowing for up to
+27 different I2C addresses, depending on the package.
+
+Optional properties:
+
+ - vcc-supply:		A regulator node that is connected to the Vcc pin
+			(2.7V - 5.5V). If specified, the regulator will be
+			enabled at probe time and disabled when the driver
+			is removed.
+
+ - nxp,os-fault-queue:	Specifies the number of faults that must occur
+			consecutively to activate the OS output pin.
+			Valid numbers are 1 (default), 2, 4 and 6.
+
+ - nxp,os-active-high:	Specifies that the OS pin should be in active-high
+			mode. By default, it is active-low.
+
+ - nxp,os-mode-interrupt: Configures the device to operate the OS pin
+			  as an interrupt rather than a comparator. Please
+			  refer to the datasheet for information about the
+			  differences.
+
+ - nxp,sample-period-ms: Configures the sample period of the device in
+			 milliseconds. Valid values are multiples of 100
+			 up to 3100.
+
+ - nxp,overtemperature-shutdown-millicelsius:
+			Configures the temperature threshold at which the
+			device shuts down, in milli-celcius.
+			Values are given as signed integer and are valid
+			in the range from -55000 up to +125000.
+
+ - nxp,hysteresis-millicelsius:
+			Configures the temperature threshold for OS pin
+			operation, in milli-celcius.
+			Values are given as signed integer and are valid
+			in the range from -55000 up to +125000.
+
+Example:
+
+pct2075@48 {
+	compatible = "nxp,pct2075";
+	reg = <0x48>; /* A0, A1, A2 = low */
+	nxp,os-active-high;
+	nxp,os-mode-interrupt;
+	nxp,sample-period-ms = <1000>;
+	nxp,overtemperature-shutdown-millicelsius = <110000>;
+	nxp,hysteresis-millicelsius = <(-10000)>;
+};
+
-- 
2.21.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux