Re: [PATCH] ARM: imx25: provide a fixed regulator for usb phys

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 19-06-26 02:40, Peter Chen wrote:
>  
> > Subject: [PATCH] ARM: imx25: provide a fixed regulator for usb phys
> > 
> > The usb phys are internal to the SoC and so it their 5V supply. With this regulator
> > added explicitly the following (harmless) boot messages go away:
> > 
> > 	usb_phy_generic usbphy:usb-phy@0: usbphy:usb-phy@0 supply vcc not
> > found, using dummy regulator
> > 	usb_phy_generic usbphy:usb-phy@1: usbphy:usb-phy@1 supply vcc not
> > found, using dummy regulator
> > 
> 
> To eliminate the warning message, I suggest doing below changes, as vcc
> supply is not mandatory.
> 
> diff --git a/drivers/usb/phy/phy-generic.c b/drivers/usb/phy/phy-generic.c
> index a53b89be5324..01a5ff1a0515 100644
> --- a/drivers/usb/phy/phy-generic.c
> +++ b/drivers/usb/phy/phy-generic.c
> @@ -275,7 +275,7 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop,
>                 }   
>         }   
>  
> -       nop->vcc = devm_regulator_get(dev, "vcc");
> +       nop->vcc = devm_regulator_get_optional(dev, "vcc");

Is the regulator optional? IMHO this shouldn't be the fix. I think the
right fix is Uwe's approach.

Regards,
  Marco

>         if (IS_ERR(nop->vcc)) {
>                 dev_dbg(dev, "Error getting vcc regulator: %ld\n",
>                                         PTR_ERR(nop->vcc));
> 
> Peter
> 
> > Signed-off-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
> > ---
> > Hello,
> > 
> > note I'm an USB noob, so please consider carefully before applying :-) I also put the
> > regulator near the usbphy node instead of in alphabetic order. Not sure what is
> > sensible/usual here, too.
> > 
> > Best regards
> > Uwe
> > 
> >  arch/arm/boot/dts/imx25.dtsi | 9 +++++++++
> >  1 file changed, 9 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi
> > --- a/arch/arm/boot/dts/imx25.dtsi
> > +++ b/arch/arm/boot/dts/imx25.dtsi
> > @@ -614,6 +614,11 @@
> >  		};
> >  	};
> > 
> > +	reg_usb: regulator_usbphy {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "usb-phy supply";
> > +	};
> > +
> >  	usbphy {
> >  		compatible = "simple-bus";
> >  		#address-cells = <1>;
> > @@ -623,12 +630,14 @@
> >  			reg = <0>;
> >  			compatible = "usb-nop-xceiv";
> >  			#phy-cells = <0>;
> > +			vcc-supply = <&reg_usb>;
> >  		};
> > 
> >  		usbphy1: usb-phy@1 {
> >  			reg = <1>;
> >  			compatible = "usb-nop-xceiv";
> >  			#phy-cells = <0>;
> > +			vcc-supply = <&reg_usb>;
> >  		};
> >  	};
> >  };
> > --
> > 2.20.1
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux