On 24/06/2019 11:45:37+0000, Claudiu Manoil wrote:
> Hi Andrew,
>
> >-----Original Message-----
> >From: Andrew Lunn <andrew@xxxxxxx>
> >Sent: Friday, June 21, 2019 7:50 PM
> >To: Claudiu Manoil <claudiu.manoil@xxxxxxx>
> >Cc: David S . Miller <davem@xxxxxxxxxxxxx>; devicetree@xxxxxxxxxxxxxxx;
> >Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>; netdev@xxxxxxxxxxxxxxx;
> >Alexandru Marginean <alexandru.marginean@xxxxxxx>; linux-
> >kernel@xxxxxxxxxxxxxxx; UNGLinuxDriver@xxxxxxxxxxxxx; Allan Nielsen
> ><Allan.Nielsen@xxxxxxxxxxxxx>; Rob Herring <robh+dt@xxxxxxxxxx>; linux-
> >arm-kernel@xxxxxxxxxxxxxxxxxxx
> >Subject: Re: [PATCH net-next 4/6] arm64: dts: fsl: ls1028a: Add Felix switch port
> >DT node
> >
> >On Fri, Jun 21, 2019 at 06:38:50PM +0300, Claudiu Manoil wrote:
> >> The switch device features 6 ports, 4 with external links
> >> and 2 internally facing to the ls1028a SoC and connected via
> >> fixed links to 2 internal enetc ethernet controller ports.
> >
> >Hi Claudiu
> >
> >> + switch@0,5 {
> >> + compatible = "mscc,felix-switch";
> >> + reg = <0x000500 0 0 0 0>;
> >> +
> >> + ethernet-ports {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + /* external ports */
> >> + switch_port0: port@0 {
> >> + reg = <0>;
> >> + };
> >> + switch_port1: port@1 {
> >> + reg = <1>;
> >> + };
> >> + switch_port2: port@2 {
> >> + reg = <2>;
> >> + };
> >> + switch_port3: port@3 {
> >> + reg = <3>;
> >> + };
> >> + /* internal to-cpu ports */
> >> + port@4 {
> >> + reg = <4>;
> >> + fixed-link {
> >> + speed = <1000>;
> >> + full-duplex;
> >> + };
> >> + };
> >> + port@5 {
> >> + reg = <5>;
> >> + fixed-link {
> >> + speed = <1000>;
> >> + full-duplex;
> >> + };
> >> + };
> >> + };
> >> + };
> >
> >This sounds like a DSA setup, where you have SoC ports connected to
> >the switch. With DSA, the CPU ports of the switch are special. We
> >don't create netdev's for them, the binding explicitly list which SoC
> >interface they are bound to, etc.
> >
> >What model are you using here? I'm just trying to understand the setup
> >to ensure it is consistent with the swichdev model.
> >
>
> Yeah, there are 2 ethernet controller ports (managed by the enetc driver)
> connected inside the SoC via SGMII links to 2 of the switch ports, one of
> these switch ports can be configured as CPU port (with follow-up patches).
>
> This configuration may look prettier on DSA, but the main restriction here
> is that the entire functionality is provided by the ocelot driver which is a
> switchdev driver. I don't think it would be a good idea to copy-paste code
> from ocelot to a separate dsa driver.
>
We should probably make the ocelot driver a DSA driver then...
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
