[PATCH v5 06/10] dt-bindings: memory: Add binding for NVIDIA Tegra30 External Memory Controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add device-tree binding for NVIDIA Tegra30 External Memory Controller.
The binding is based on the Tegra124 EMC binding since hardware is
similar, although there are couple significant differences.

Note that the memory timing description is given in a platform-specific
form because there is no detailed information on how to convert a
typical-common DDR timing into the register values. The timing format is
borrowed from downstream kernel, hence there is no hurdle in regards to
upstreaming of memory timings for the boards.

Acked-by: Peter De Schrijver <pdeschrijver@xxxxxxxxxx>
Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
---
 .../memory-controllers/nvidia,tegra30-emc.txt | 249 ++++++++++++++++++
 1 file changed, 249 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt

diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt
new file mode 100644
index 000000000000..c2bc1dbcaa07
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.txt
@@ -0,0 +1,249 @@
+NVIDIA Tegra30 SoC EMC (external memory controller)
+====================================================
+
+Required properties :
+- compatible : Should be "nvidia,tegra30-emc".
+- reg : physical base address and length of the controller's registers.
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- interrupts : Should contain EMC General interrupt.
+- clocks : Should contain EMC clock.
+- nvidia,memory-controller : phandle of the MC driver.
+
+The node should contain a "emc-timings" subnode for each supported RAM type
+(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address
+being its RAM_CODE.
+
+Required properties for "emc-timings" nodes :
+- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is
+used for.
+
+Each "emc-timings" node should contain a "timing" subnode for every supported
+EMC clock rate. The "timing" subnodes should have the clock rate in Hz as
+their unit address.
+
+Required properties for "timing" nodes :
+- clock-frequency : Should contain the memory clock rate in Hz.
+- The following properties contain EMC timing characterization values
+(specified in the board documentation) :
+  - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL
+  - nvidia,emc-mode-1 : Mode Register 1
+  - nvidia,emc-mode-2 : Mode Register 2
+  - nvidia,emc-mode-reset : Mode Register 0
+  - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change
+  - nvidia,emc-cfg-dyn-self-ref : dynamic self-refresh enabled
+  - nvidia,emc-cfg-periodic-qrst : FBIO "read" FIFO periodic resetting enabled
+- nvidia,emc-configuration : EMC timing characterization data. These are the
+registers (see section "18.13.2 EMC Registers" in the TRM) whose values need to
+be specified, according to the board documentation:
+
+	EMC_RC
+	EMC_RFC
+	EMC_RAS
+	EMC_RP
+	EMC_R2W
+	EMC_W2R
+	EMC_R2P
+	EMC_W2P
+	EMC_RD_RCD
+	EMC_WR_RCD
+	EMC_RRD
+	EMC_REXT
+	EMC_WEXT
+	EMC_WDV
+	EMC_QUSE
+	EMC_QRST
+	EMC_QSAFE
+	EMC_RDV
+	EMC_REFRESH
+	EMC_BURST_REFRESH_NUM
+	EMC_PRE_REFRESH_REQ_CNT
+	EMC_PDEX2WR
+	EMC_PDEX2RD
+	EMC_PCHG2PDEN
+	EMC_ACT2PDEN
+	EMC_AR2PDEN
+	EMC_RW2PDEN
+	EMC_TXSR
+	EMC_TXSRDLL
+	EMC_TCKE
+	EMC_TFAW
+	EMC_TRPAB
+	EMC_TCLKSTABLE
+	EMC_TCLKSTOP
+	EMC_TREFBW
+	EMC_QUSE_EXTRA
+	EMC_FBIO_CFG6
+	EMC_ODT_WRITE
+	EMC_ODT_READ
+	EMC_FBIO_CFG5
+	EMC_CFG_DIG_DLL
+	EMC_CFG_DIG_DLL_PERIOD
+	EMC_DLL_XFORM_DQS0
+	EMC_DLL_XFORM_DQS1
+	EMC_DLL_XFORM_DQS2
+	EMC_DLL_XFORM_DQS3
+	EMC_DLL_XFORM_DQS4
+	EMC_DLL_XFORM_DQS5
+	EMC_DLL_XFORM_DQS6
+	EMC_DLL_XFORM_DQS7
+	EMC_DLL_XFORM_QUSE0
+	EMC_DLL_XFORM_QUSE1
+	EMC_DLL_XFORM_QUSE2
+	EMC_DLL_XFORM_QUSE3
+	EMC_DLL_XFORM_QUSE4
+	EMC_DLL_XFORM_QUSE5
+	EMC_DLL_XFORM_QUSE6
+	EMC_DLL_XFORM_QUSE7
+	EMC_DLI_TRIM_TXDQS0
+	EMC_DLI_TRIM_TXDQS1
+	EMC_DLI_TRIM_TXDQS2
+	EMC_DLI_TRIM_TXDQS3
+	EMC_DLI_TRIM_TXDQS4
+	EMC_DLI_TRIM_TXDQS5
+	EMC_DLI_TRIM_TXDQS6
+	EMC_DLI_TRIM_TXDQS7
+	EMC_DLL_XFORM_DQ0
+	EMC_DLL_XFORM_DQ1
+	EMC_DLL_XFORM_DQ2
+	EMC_DLL_XFORM_DQ3
+	EMC_XM2CMDPADCTRL
+	EMC_XM2DQSPADCTRL2
+	EMC_XM2DQPADCTRL2
+	EMC_XM2CLKPADCTRL
+	EMC_XM2COMPPADCTRL
+	EMC_XM2VTTGENPADCTRL
+	EMC_XM2VTTGENPADCTRL2
+	EMC_XM2QUSEPADCTRL
+	EMC_XM2DQSPADCTRL3
+	EMC_CTT_TERM_CTRL
+	EMC_ZCAL_INTERVAL
+	EMC_ZCAL_WAIT_CNT
+	EMC_MRS_WAIT_CNT
+	EMC_AUTO_CAL_CONFIG
+	EMC_CTT
+	EMC_CTT_DURATION
+	EMC_DYN_SELF_REF_CONTROL
+	EMC_FBIO_SPARE
+	EMC_CFG_RSV
+
+Example:
+
+	external-memory-controller {
+		compatible = "nvidia,tegra30-emc";
+		reg = <0x7000f400 0x400>;
+		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA30_CLK_EMC>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nvidia,memory-controller = <&mc>;
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref = <0x00000000>;
+				nvidia,emc-cfg-periodic-qrst = <0x00000001>;
+
+				nvidia,emc-configuration = <
+					0x00000020 /* EMC_RC */
+					0x0000006a /* EMC_RFC */
+					0x00000017 /* EMC_RAS */
+					0x00000007 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000c /* EMC_W2R */
+					0x00000003 /* EMC_R2P */
+					0x00000011 /* EMC_W2P */
+					0x00000007 /* EMC_RD_RCD */
+					0x00000007 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001412 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x0000000e /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000c /* EMC_AR2PDEN */
+					0x00000016 /* EMC_RW2PDEN */
+					0x00000072 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000015 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000006 /* EMC_TCLKSTABLE */
+					0x00000007 /* EMC_TCLKSTOP */
+					0x00001453 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf00b0191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00000008 /* EMC_DLL_XFORM_DQS0 */
+					0x00000008 /* EMC_DLL_XFORM_DQS1 */
+					0x00000008 /* EMC_DLL_XFORM_DQS2 */
+					0x00000008 /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000a /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x0c000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0155000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+	};
-- 
2.22.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux