Re: [PATCH 1/1] ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 06.06.2019 11:06, Igor Opaniuk wrote:
> From: Igor Opaniuk <igor.opaniuk@xxxxxxxxxxx>
> 
> Allows to use the SD interface at a higher speed mode if the card
> supports it. For this the signaling voltage is switched from 3.3V to
> 1.8V under the usdhc1's drivers control.
> 
> Signed-off-by: Igor Opaniuk <igor.opaniuk@xxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/imx6ul.dtsi                  |  4 ++++
>  arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 11 +++++++++--
>  arch/arm/boot/dts/imx6ull-colibri.dtsi         |  6 ++++++
>  3 files changed, 19 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
> index fc388b84bf22..91a0ced44e27 100644
> --- a/arch/arm/boot/dts/imx6ul.dtsi
> +++ b/arch/arm/boot/dts/imx6ul.dtsi
> @@ -857,6 +857,8 @@
>  					 <&clks IMX6UL_CLK_USDHC1>,
>  					 <&clks IMX6UL_CLK_USDHC1>;
>  				clock-names = "ipg", "ahb", "per";
> +				fsl,tuning-step= <2>;
> +				fsl,tuning-start-tap = <20>;
>  				bus-width = <4>;
>  				status = "disabled";
>  			};
> @@ -870,6 +872,8 @@
>  					 <&clks IMX6UL_CLK_USDHC2>;
>  				clock-names = "ipg", "ahb", "per";
>  				bus-width = <4>;
> +				fsl,tuning-step= <2>;
> +				fsl,tuning-start-tap = <20>;
>  				status = "disabled";
>  			};
>  
> diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> index 006690ea98c0..7dc7770cf52c 100644
> --- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> +++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
> @@ -145,13 +145,20 @@
>  };
>  
>  &usdhc1 {
> -	pinctrl-names = "default";
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
>  	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
> -	no-1-8-v;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
> +	pinctrl-2 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;

Should that not be pinctrl_usdhc1_200mhz?

--
Stefan

> +	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
>  	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
>  	disable-wp;
>  	wakeup-source;
>  	keep-power-in-suspend;
>  	vmmc-supply = <&reg_3v3>;
> +	vqmmc-supply = <&reg_sd1_vmmc>;
> +	sd-uhs-sdr12;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr50;
> +	sd-uhs-sdr104;
>  	status = "okay";
>  };
> diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi
> b/arch/arm/boot/dts/imx6ull-colibri.dtsi
> index 9ad1da159768..d56728f03c35 100644
> --- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
> @@ -545,6 +545,12 @@
>  		>;
>  	};
>  
> +	pinctrl_snvs_usdhc1_sleep_cd: snvs-usdhc1-cd-grp-slp {
> +		fsl,pins = <
> +			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x0
> +		>;
> +	};
> +
>  	pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
>  		fsl,pins = <
>  			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x14



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux