Re: [PATCH 4/4] arm64: DTS: allwinner: a64: enable ANX6345 bridge on Teres-I

[Vasily Khoruzhick <anarsoul@xxxxxxxxx>]

On Tue, May 14, 2019 at 9:03 AM Torsten Duwe <duwe@xxxxxx> wrote:
>
> From: Icenowy Zheng <icenowy@xxxxxxx>
>
> TERES-I has an ANX6345 bridge connected to the RGB666 LCD output, and
> the I2C controlling signals are connected to I2C0 bus.
>
> Enable it in the device tree.
>
> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> Signed-off-by: Torsten Duwe <duwe@xxxxxxx>
> ---
>
> originally: patchwork.kernel.org/patch/10646867
>
> Changed the reset polarity, which is active low,
> according to the (terse) datasheet, Teres-I and pinebook schematics,
> and the confusing parts of the linux driver code (not yet included here).
> Active low -> no more confusion.
>
> ---
>  .../boot/dts/allwinner/sun50i-a64-teres-i.dts | 40 +++++++++++++++++--
>  1 file changed, 36 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> index c455b24dd079..bc1d0d6c0672 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> @@ -72,20 +72,38 @@
>         };
>  };
>
> +&de {
> +       status = "okay";
> +};
> +
>  &ehci1 {
>         status = "okay";
>  };
>
>
> -/* The ANX6345 eDP-bridge is on i2c0. There is no linux (mainline)
> - * driver for this chip at the moment, the bootloader initializes it.
> - * However it can be accessed with the i2c-dev driver from user space.
> - */
>  &i2c0 {
>         clock-frequency = <100000>;
>         pinctrl-names = "default";
>         pinctrl-0 = <&i2c0_pins>;
>         status = "okay";
> +
> +       anx6345: anx6345@38 {
> +               compatible = "analogix,anx6345";
> +               reg = <0x38>;
> +               reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
> +               dvdd25-supply = <&reg_dldo2>;
> +               dvdd12-supply = <&reg_dldo3>;
> +
> +               port {
> +                       anx6345_in: endpoint {
> +                               remote-endpoint = <&tcon0_out_anx6345>;
> +                       };
> +               };

It doesn't comply with bindings document. You need to add out endpoint
as well, and to do so you need to add bindings for eDP connector first
and then implement panel driver.
See Rob's suggestions here: http://patchwork.ozlabs.org/patch/1042593/

> +       };
> +};
> +
> +&mixer0 {
> +       status = "okay";
>  };
>
>  &mmc0 {
> @@ -258,6 +276,20 @@
>         vcc-hdmi-supply = <&reg_dldo1>;
>  };
>
> +&tcon0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&lcd_rgb666_pins>;
> +
> +       status = "okay";
> +};
> +
> +&tcon0_out {
> +       tcon0_out_anx6345: endpoint@0 {
> +               reg = <0>;
> +               remote-endpoint = <&anx6345_in>;
> +       };
> +};
> +
>  &uart0 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&uart0_pb_pins>;