Re: [PATCH V3 4/8] memory: tegra: Add Tegra210 EMC clock driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 5/14/19 12:54 AM, Dmitry Osipenko wrote:
10.05.2019 11:47, Joseph Lo пишет:
This is the initial patch for Tegra210 EMC clock driver, which doesn't
include the support code and detail sequence for clock scaling yet.

The driver is designed to support LPDDR4 SDRAM. Because of the LPDDR4
devices need to do initial time training before it can be used, the
firmware will help to do that at early boot stage. Then, the trained
table for the rates we support will pass to the kernel via DT. So the
driver can get the trained table for clock scaling support.

For the higher rate support (above 800MHz), the periodic training is
needed for the timing compensation. So basically, two methodologies for
clock scaling are supported, one is following the clock changing
sequence to update the EMC table to EMC registers and another is if the
rate needs periodic training, then we will start a timer to do that
periodically until it scales to the lower rate.

Based on the work of Peter De Schrijver <pdeschrijver@xxxxxxxxxx>.

Signed-off-by: Joseph Lo <josephl@xxxxxxxxxx>
---
v3:
- address almost all the comments from the previous version
- remove the DT parser of EMC table
- The EMC table is passing as a binary blob now.
---
snip.
+#ifdef CONFIG_DEBUG_FS
+static int emc_stats_show(struct seq_file *s, void *data)
+{
+	int i;
+	struct tegra_emc *emc = (struct tegra_emc *)s->private;

There is no need for casting of the void*.

+
+	if (!emc->emc_table_size || !seq)
+		return 0;
+
+	emc_last_stats_update(TEGRA_EMC_MAX_FREQS);
+
+	seq_printf(s, "%-10s %-10s\n", "rate kHz", "time");
+	for (i = 0; i < emc->emc_table_size; i++) {
+		if (emc_clk_sel[i].input == NULL)
+			continue;
+
+		seq_printf(s, "%-10u %-10llu\n",
+			   emc->emc_table[i].rate,
+			   jiffies_64_to_clock_t(
+			   emc_stats.time_at_clock[i]));
+	}
+	seq_printf(s, "%-15s %llu\n", "transitions:",
+		   emc_stats.clkchange_count);
+	seq_printf(s, "%-15s %llu\n", "time-stamp:",
+		   jiffies_64_to_clock_t(emc_stats.last_update));

Devfreq subsystem has the transition stats too and it is a bit more advanced than what you have here.

  cat /sys/class/devfreq/devfreq0/trans_stat
       From  :   To
             :  50000000 100000000 150000000 300000000 600000000   time(ms)
  *  50000000:         0         4         4         0        46 118096210
    100000000:        21         0         0         0         5     15460
    150000000:        10         9         0         0     10560  20213940
    300000000:        13         6      5058         0     22375   6848690
    600000000:        11         7      5517     27452         0  11958990
  Total transition : 71098

Hence I'm questioning the necessity of the debug-info duplication.


Okay, will remove the statistic data in the next version. BTW, I think we will use Interconnect framework for the EMC BW manager for the Tegra chips >= T210.

Thanks,
Joseph




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux