Generally, the output clock pin is only used for testing and only serves
as a source of RF noise after this. It could be used to daisy-chain
PHYs, but this is uncommon. Since the PHY can disable the output, make
doing so an option. I do this by adding another enumeration to the
allowed values of ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep
clock output setting as is", which, depending on PHY strapping, might
not be outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the
previous behavior in this case).
Out of range values were silently converted into
DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error.
Cc: Andrew Lunn <andrew@xxxxxxx>
Cc: Florian Fainelli <f.fainelli@xxxxxxxxx>
Cc: Heiner Kallweit <hkallweit1@xxxxxxxxx>
Signed-off-by: Trent Piepho <tpiepho@xxxxxxxxxx>
---
drivers/net/phy/dp83867.c | 36 ++++++++++++++++++++++++++----------
1 file changed, 26 insertions(+), 10 deletions(-)
diff --git a/drivers/net/phy/dp83867.c b/drivers/net/phy/dp83867.c
index fd35131a0c39..420729cd6025 100644
--- a/drivers/net/phy/dp83867.c
+++ b/drivers/net/phy/dp83867.c
@@ -68,6 +68,7 @@
#define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX 0x0
#define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN 0x1f
+#define DP83867_IO_MUX_CFG_CLK_O_DISABLE BIT(6)
#define DP83867_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8)
#define DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT 8
@@ -87,7 +88,8 @@ struct dp83867_private {
int io_impedance;
int port_mirroring;
bool rxctrl_strap_quirk;
- int clk_output_sel;
+ bool set_clk_output;
+ u32 clk_output_sel;
};
static int dp83867_ack_interrupt(struct phy_device *phydev)
@@ -154,11 +156,16 @@ static int dp83867_of_init(struct phy_device *phydev)
/* Optional configuration */
ret = of_property_read_u32(of_node, "ti,clk-output-sel",
&dp83867->clk_output_sel);
- if (ret || dp83867->clk_output_sel > DP83867_CLK_O_SEL_REF_CLK)
- /* Keep the default value if ti,clk-output-sel is not set
- * or too high
- */
- dp83867->clk_output_sel = DP83867_CLK_O_SEL_REF_CLK;
+ /* If not set, keep default */
+ if (!ret) {
+ dp83867->set_clk_output = true;
+ if (dp83867->clk_output_sel > DP83867_CLK_O_SEL_REF_CLK &&
+ dp83867->clk_output_sel != DP83867_CLK_O_SEL_OFF) {
+ phydev_err(phydev, "ti,clk-output-sel value %u out of range\n",
+ dp83867->clk_output_sel);
+ return -EINVAL;
+ }
+ }
if (of_property_read_bool(of_node, "ti,max-output-impedance"))
dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX;
@@ -288,11 +295,20 @@ static int dp83867_config_init(struct phy_device *phydev)
dp83867_config_port_mirroring(phydev);
/* Clock output selection if muxing property is set */
- if (dp83867->clk_output_sel != DP83867_CLK_O_SEL_REF_CLK)
+ if (dp83867->set_clk_output) {
+ u16 mask = DP83867_IO_MUX_CFG_CLK_O_DISABLE;
+
+ if (dp83867->clk_output_sel == DP83867_CLK_O_SEL_OFF) {
+ val = DP83867_IO_MUX_CFG_CLK_O_DISABLE;
+ } else {
+ mask |= DP83867_IO_MUX_CFG_CLK_O_SEL_MASK;
+ val = dp83867->clk_output_sel <<
+ DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT;
+ }
+
phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG,
- DP83867_IO_MUX_CFG_CLK_O_SEL_MASK,
- dp83867->clk_output_sel <<
- DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT);
+ mask, val);
+ }
return 0;
}
--
2.14.5
