On 5/2/19 04:33, Mark Brown wrote:
> On Mon, Apr 29, 2019 at 02:31:55PM +0200, Jorge Ramirez wrote:
>> On 4/27/19 20:21, Mark Brown wrote:
>
>>> Since the point of this change is AFAICT that this regulator only has a
>>> single linear range it seems like it should just be able to use the
>>> existing generic functions shouldn't it?
>
>> yes that would have been ideal but it does not seem to be the case for
>> this hardware.
>
>> The register that stores the voltage range for all other SPMI regulators
>> (SPMI_COMMON_REG_VOLTAGE_RANGE 0x40) is used by something else in the
>> HFS430: SPMI_HFS430_REG_VOLTAGE_LB 0x40 stores the voltage level in two
>> bytes 0x40 and 0x41;
>
>> This overlap really what is creating the pain: HFS430 cant use 0x40 to
>> store the range (even if it is only one)
>
>> so yeah, most of the changes in the patch are working around this fact.
>
> I'm not sure I follow here, sorry - I can see that the driver needs a
> custom get/set selector operation but shouldn't it be able to use the
> standard list and map operations for linear ranges?
I agree it should, but unfortunately that is not the case; when I first
posted the patch I was concerned that for a regulator to be supported by
this driver it should obey to the driver's internals (ie: comply with
all of the spmi_common_regulator_registers definitions).
However, since there was just a single range to support, the
modifications I had to do to support this SPMI regulator were minimal -
hence why I opted for the changes under discussion instead of writing a
new driver (which IMO it is an overkill).
what do you think?
>
>>
>> enum spmi_common_regulator_registers {
>> SPMI_COMMON_REG_DIG_MAJOR_REV = 0x01,
>> SPMI_COMMON_REG_TYPE = 0x04,
>> SPMI_COMMON_REG_SUBTYPE = 0x05,
>> SPMI_COMMON_REG_VOLTAGE_RANGE = 0x40, ******
>> SPMI_COMMON_REG_VOLTAGE_SET = 0x41,
>> SPMI_COMMON_REG_MODE = 0x45,
>> SPMI_COMMON_REG_ENABLE = 0x46,
>> SPMI_COMMON_REG_PULL_DOWN = 0x48,
>> SPMI_COMMON_REG_SOFT_START = 0x4c,
>> SPMI_COMMON_REG_STEP_CTRL = 0x61,
>> };
>>
>> enum spmi_hfs430_registers {
>> SPMI_HFS430_REG_VOLTAGE_LB = 0x40, *******
>> SPMI_HFS430_REG_VOLTAGE_VALID_LB = 0x42,
ah, this definition I can remove and use the common one above. I'll do that.
>> SPMI_HFS430_REG_MODE = 0x45,
>> };
>>
>> It just needs it's own
>>> set/get_voltage_sel() operations. As far as I can see the main thing
>>> the driver is doing with the custom stuff is handling the fact that
>>> there's multiple ranges but that's not an issue for this regulator.
>>> It's possible I'm missing something there but that was the main thing
>>> (and we do have some generic support for multiple linear ranges in the
>>> helper code already, can't remember why this driver isn't using that -
>>> the ranges overlap IIRC?).
>>>
>>> TBH looking at the uses of find_range() I'm not sure they're 100%
>>> sensible as they are - the existing _time_sel() is assuming we only need
>>> to work out the ramp time between voltages in the same range which is
>>> going to have trouble.
>>>
>>
