Add the DT binding documentation for Interrupt router driver. Signed-off-by: Lokesh Vutla <lokeshvutla@xxxxxx> --- Changes since v7: - Changes interrupt cells to 2. .../interrupt-controller/ti,sci-intr.txt | 82 +++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 83 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt new file mode 100644 index 000000000000..1a8718f8855d --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt @@ -0,0 +1,82 @@ +Texas Instruments K3 Interrupt Router +===================================== + +The Interrupt Router (INTR) module provides a mechanism to mux M +interrupt inputs to N interrupt outputs, where all M inputs are selectable +to be driven per N output. An Interrupt Router can either handle edge triggered +or level triggered interrupts and that is fixed in hardware. + + Interrupt Router + +----------------------+ + | Inputs Outputs | + +-------+ | +------+ +-----+ | + | GPIO |----------->| | irq0 | | 0 | | Host IRQ + +-------+ | +------+ +-----+ | controller + | . . | +-------+ + +-------+ | . . |----->| IRQ | + | INTA |----------->| . . | +-------+ + +-------+ | . +-----+ | + | +------+ | N | | + | | irqM | +-----+ | + | +------+ | + | | + +----------------------+ + +There is one register per output (MUXCNTL_N) that controls the selection. +Configuration of these MUXCNTL_N registers is done by a system controller +(like the Device Memory and Security Controller on K3 AM654 SoC). System +controller will keep track of the used and unused registers within the Router. +Driver should request the system controller to get the range of GIC IRQs +assigned to the requesting hosts. It is the drivers responsibility to keep +track of Host IRQs. + +Communication between the host processor running an OS and the system +controller happens through a protocol called TI System Control Interface +(TISCI protocol). For more details refer: +Documentation/devicetree/bindings/arm/keystone/ti,sci.txt + +TISCI Interrupt Router Node: +---------------------------- +Required Properties: +- compatible: Must be "ti,sci-intr". +- ti,intr-trigger-type: Should be one of the following: + 1: If intr supports edge triggered interrupts. + 4: If intr supports level triggered interrupts. +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value should be 2. + First cell should contain the TISCI device ID of source + Second cell should contain the interrupt source offset + within the device. +- ti,sci: Phandle to TI-SCI compatible System controller node. +- ti,sci-dst-id: TISCI device ID of the destination IRQ controller. +- ti,sci-rm-range-girq: Array of TISCI subtype ids representing the host irqs + assigned to this interrupt router. Each subtype id + corresponds to a range of host irqs. + +For more details on TISCI IRQ resource management refer: +http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html + +Example: +-------- +The following example demonstrates both interrupt router node and the consumer +node(main gpio) on the AM654 SoC: + +main_intr: interrupt-controller0 { + compatible = "ti,sci-intr"; + ti,intr-trigger-type = <1>; + interrupt-controller; + interrupt-parent = <&gic500>; + #interrupt-cells = <2>; + ti,sci = <&dmsc>; + ti,sci-dst-id = <56>; + ti,sci-rm-range-girq = <0x1>; +}; + +main_gpio0: gpio@600000 { + ... + interrupt-parent = <&main_intr>; + interrupts = <57 256>, <57 257>, <57 258>, + <57 259>, <57 260>, <57 261>; + ... +}; diff --git a/MAINTAINERS b/MAINTAINERS index 5c38f21aee78..91b4dcfb47f4 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15350,6 +15350,7 @@ F: Documentation/devicetree/bindings/reset/ti,sci-reset.txt F: Documentation/devicetree/bindings/clock/ti,sci-clk.txt F: drivers/clk/keystone/sci-clk.c F: drivers/reset/reset-ti-sci.c +F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt Texas Instruments ASoC drivers M: Peter Ujfalusi <peter.ujfalusi@xxxxxx> -- 2.21.0
