Re: [PATCH v7 5/6] dt-bindings: display: sii902x: Add HDMI audio bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Apr 26, 2019 at 8:23 AM Jyri Sarha <jsarha@xxxxxx> wrote:
>
> The sii902x chip family supports also HDMI audio. Add binding for
> describing the necessary i2s and mclk wiring for it.
>
> Signed-off-by: Jyri Sarha <jsarha@xxxxxx>
> ---
>  .../bindings/display/bridge/sii902x.txt       | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> index c4c1855ca654..b5168a0e3a2b 100644
> --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> @@ -9,6 +9,41 @@ Optional properties:
>           about hotplug events.
>         - reset-gpios: OF device-tree gpio specification for RST_N pin.
>
> +       HDMI audio properties:
> +       - #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin
> +          is wired, <1> if the both are wired. HDMI audio is
> +          configured only if this property is found.
> +       - sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3
> +          Each integer indicates which i2s pin is connected to which
> +          audio fifo. The first integer selects i2s audio pin for the
> +          first audio fifo#0 (HDMI channels 1&2), second for fifo#1
> +          (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
> +          pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
> +          but there can be no gaps. E.g. an i2s pin must be mapped to
> +          fifo#0 and fifo#1 before mapping a channel to fifo#2. Default
> +          value is <0>, describing SD0 pin beiging routed to hdmi audio
> +          fifo #0.
> +       - clocks: phandle and clock specifier for each clock listed in
> +           the clock-names property
> +       - clock-names: "mclk"
> +          Describes SII902x MCLK input. MCLK is used to produce
> +          HDMI audio CTS values. This property is required if
> +          "#sound-dai-cells"-property is present. This property follows
> +          Documentation/devicetree/bindings/clock/clock-bindings.txt
> +          consumer binding.
> +
> +       If HDMI audio is configured the sii902x device becomes an I2S
> +       and/or spdif audio codec component (e.g a digital audio sink),
> +       that can be used in configuring a full audio devices with
> +       simple-card or audio-graph-card binding. See their binding
> +       documents on how to describe the way the sii902x device is
> +       connected to the rest of the audio system:
> +       Documentation/devicetree/bindings/sound/simple-card.txt
> +       Documentation/devicetree/bindings/sound/audio-graph-card.txt
> +       Note: In case of the audio-graph-card binding the used port
> +       index should be 3 or higher to avoid conflict with video ports

Drop the 'or higher'. The port number should be known and fixed.

With that,

Reviewed-by: Rob Herring <robh@xxxxxxxxxx>



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux