On Wed, Apr 24, 2019 at 5:29 AM Andrew Peng <pengms1@xxxxxxxxxx> wrote:
>
> Initial introduction of Lenovo Hr630 family equipped with
> Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
> with a ASPEED ast2500 BMC manufactured by Lenovo.
> Specifically, This adds the Hr630 platform device tree file
> used by the Hr630 BMC machines.
>
> This also adds an entry of Hr630 device tree file in Makefile
>
> Signed-off-by: Andrew Peng <pengms1@xxxxxxxxxx>
> Signed-off-by: Yonghui Liu <liuyh21@xxxxxxxxxx>
> Signed-off-by: Lisa Liu <liuyj19@xxxxxxxxxx>
> ---
> Changes in v3:
> - revise i2c switch aliases name.
> Changes in v2:
> - add i2c switch aliases name.
> - remove the unused eeprom device from DT file.
> - remove "Licensed under..." sentence.
>
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 886 ++++++++++++++++++++++++++
> 2 files changed, 888 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index f4f5aea..375e53b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1261,4 +1261,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-opp-witherspoon.dtb \
> aspeed-bmc-opp-zaius.dtb \
> aspeed-bmc-portwell-neptune.dtb \
> - aspeed-bmc-quanta-q71l.dtb
> + aspeed-bmc-quanta-q71l.dtb \
> + aspeed-bmc-lenovo-hr630.dtb
> diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> new file mode 100644
> index 0000000..5c45523
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> @@ -0,0 +1,886 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Device Tree file for Lenovo Hr630 platform
> + *
> + * Copyright (C) 2019-present Lenovo
> + */
> +
> +/dts-v1/;
> +
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "HR630 BMC";
> + compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
> +
> + aliases {
> + pca9545_i2c0 = &i2c_rbp;
> + pca9545_i2c1 = &i2c_fbp1;
> + pca9545_i2c2 = &i2c_fbp2;
> + pca9545_i2c3 = &i2c_fbp3;
> + };
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + flash_memory: region@98000000 {
> + no-map;
> + reg = <0x98000000 0x00100000>; /* 1M */
> + };
> +
> + gfx_memory: framebuffer {
> + size = <0x01000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + heartbeat {
> + gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
> + };
> +
> + fault {
> + gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
> + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
> + <&adc 8>, <&adc 9>, <&adc 10>,
> + <&adc 12>, <&adc 13>, <&adc 14>;
> + };
> +
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout.dtsi"
> + };
> +};
> +
> +&lpc_ctrl {
> + status = "okay";
> + memory-region = <&flash_memory>;
> + flash = <&spi1>;
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart5 {
> + status = "okay";
> +};
> +
> +&vuart {
> + status = "okay";
> +};
> +
> +&ibt {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii1_default>;
> + use-ncsi;
> +};
> +
> +&mac1 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
> +};
> +
> +&adc {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> + /* temp1 inlet */
> + tmp75@4e {
> + compatible = "national,lm75";
> + reg = <0x4e>;
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> + /* temp2 outlet */
> + tmp75@4d {
> + compatible = "national,lm75";
> + reg = <0x4d>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> + /* Slot 0,
> + * Slot 1,
> + * Slot 2,
> + * Slot 3
> + */
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9545";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect; /* may use mux@70 next. */
It's fine to leave mux-idle-disconnect, however the two muxes you're
worried about aren't competing under the same bus. This one lives
under i2c6 and the other i2c7, so they shouldn't interfere with each
other. Does that make sense? I missed this before because the window
only let me see part of a thing so I didn't see both in the same view
until I opened the patch in patchworks.
> +
> + i2c_rbp: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c_fbp1: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c_fbp2: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c_fbp3: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + /* Slot 0,
> + * Slot 1,
> + * Slot 2,
> + * Slot 3
> + */
> + i2c-switch@76 {
> + compatible = "nxp,pca9546";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect; /* may use mux@76 next. */
> +
> + i2c_riser2: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c_pcie4: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c_riser1: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c_ocp: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c8 {
> + status = "okay";
> +
> + eeprom@57 {
> + compatible = "atmel,24c256";
> + reg = <0x57>;
> + pagesize = <16>;
> + };
> +};
> +
> +&i2c9 {
> + status = "okay";
> +};
> +
> +&i2c10 {
> + status = "okay";
> +};
> +
> +&i2c11 {
> + status = "okay";
> +};
> +
> +&i2c12 {
> + status = "okay";
> +};
> +
> +/*
> + * Enable port A as device (via the virtual hub) and port B as
> + * host by default on the eval board. This can be easily changed
> + * by replacing the override below with &ehci0 { ... } to enable
> + * host on both ports.
> + */
> +&vhub {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&uhci {
> + status = "okay";
> +};
> +
> +&gfx {
> + status = "okay";
> + memory-region = <&gfx_memory>;
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default
> + &pinctrl_pwm1_default
> + &pinctrl_pwm2_default
> + &pinctrl_pwm3_default
> + &pinctrl_pwm4_default
> + &pinctrl_pwm5_default
> + &pinctrl_pwm6_default>;
> +
> + fan@0 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x00>;
> + };
> +
> + fan@1 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x01>;
> + };
> +
> + fan@2 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x02>;
> + };
> +
> + fan@3 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x03>;
> + };
> +
> + fan@4 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> + };
> +
> + fan@5 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> + };
> +
> + fan@6 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> + };
> +
> + fan@7 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> + };
> +
> + fan@8 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> + };
> +
> + fan@9 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> + };
> +
> + fan@10 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> + };
> +
> + fan@11 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> + };
> +
> + fan@12 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> + };
> +
> + fan@13 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> + };
> +};
> +
> +&gpio {
> +
> + pin_gpio_a0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MAC1_INT_N";
> + };
> +
> + pin_gpio_a1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MEZZ_C_PRESENT_N";
> + };
> +
> + pin_gpio_a2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_PRST";
> + };
> +
> + pin_gpio_a3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_PRST";
> + };
> +
> + pin_gpio_b5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "IRQ_BMC_PCH_SMI_LPC_N";
> + };
> +
> + pin_gpio_f0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "IRQ_BMC_PCH_NMI_R";
> + };
> +
> + pin_gpio_f1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU1_DISABLE_COD_N";
> + };
> +
> + pin_gpio_f2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "SMB_LAN_ALERT_N_MEZZ";
> + };
> +
> + pin_gpio_f3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_BUS0_RST_OUT_N";
> + };
> +
> + pin_gpio_f4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "FM_SKT0_FAULT_LED";
> + };
> +
> + pin_gpio_f5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "FM_SKT1_FAULT_LED";
> + };
> +
> + pin_gpio_f6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_BMC_CPLD_NMI";
> + };
> +
> + pin_gpio_f7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_ALERT_N";
> + };
> +
> + pin_gpio_g0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU_ERR2_LVT3_N";
> + };
> +
> + pin_gpio_g1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU_MSMI_CATERR_LVT3_N";
> + };
> +
> + pin_gpio_g2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PCH_BMC_THERMTRIP_N";
> + };
> +
> + pin_gpio_g3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_I2C_BUS7_INT_N";
> + };
> +
> + pin_gpio_g4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "FAN_PWR_CTL_N";
> + };
> +
> + pin_gpio_g5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "NFC_FD_N";
> + };
> +
> + pin_gpio_g6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_NMI_EVENT_N";
> + };
> +
> + pin_gpio_g7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "RST_BMC_PCIE_I2CMUX_N";
> + };
> +
> + pin_gpio_h0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_EPOW_N_R";
> + };
> +
> + pin_gpio_h1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_EPOW_N_R";
> + };
> +
> + pin_gpio_h2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PSU1_FFS_N_R";
> + };
> +
> + pin_gpio_h3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PSU2_FFS_N_R";
> + };
> +
> + pin_gpio_h4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_THROTTLE_N_R";
> + };
> +
> + pin_gpio_h5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_THROTTLE_N_R";
> + };
> +
> + pin_gpio_h6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_SMB_RESET_N";
> + };
> +
> + pin_gpio_h7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_SMB_RESET_N";
> + };
> +
> + pin_gpio_i1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FP_PWR_BTN_N";
> + };
> +
> + pin_gpio_i2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BIOS_RCVR_N";
> + };
> +
> + pin_gpio_i3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_INTRUDED_COVER";
> + };
> +
> + pin_gpio_j2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_BIOS_UPDATE_N";
> + };
> +
> + pin_gpio_j3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "RST_BMC_HDD_I2CMUX_N";
> + };
> +
> + pin_gpio_q4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MEZZ_A_PRESENT_N";
> + };
> +
> + pin_gpio_q5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "VGA_FRONT_PRES_N";
> + };
> +
> + pin_gpio_q6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "I2C_RISER1_INT_N";
> + };
> +
> + pin_gpio_q7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "NCSI_CABLE_DET_N";
> + };
> +
> + pin_gpio_r0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FP_RST_BTN_N";
> + };
> +
> + pin_gpio_r2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG1_DETECT_N";
> + };
> +
> + pin_gpio_r3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG2_DETECT_N";
> + };
> +
> + pin_gpio_r4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG3_DETECT_N";
> + };
> +
> + pin_gpio_r5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "VIDEO_CABLE_DETECT_N";
> + };
> +
> + pin_gpio_s0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_PS_RAPIDON_WAKE_R_N";
> + };
> +
> + pin_gpio_s1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HOST_TPM_PP_BUF";
> + };
> +
> + pin_gpio_s2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_VGA_SW";
> + };
> +
> + pin_gpio_s3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_SML0_ALERT_MUX_N";
> + };
> +
> + pin_gpio_s4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
> + output;
> + line-name = "VBAT_EN_N";
> + };
> +
> + pin_gpio_s5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_4";
> + };
> +
> + pin_gpio_s6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PU_BMC_GPIOS6";
> + };
> +
> + pin_gpio_s7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "I2C_BUS7_RESET_N";
> + };
> +
> + pin_gpio_y0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_NCSI_MUX_CTL_S0";
> + };
> +
> + pin_gpio_y1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_NCSI_MUX_CTL_S1";
> + };
> +
> + pin_gpio_y2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "UID_ALERT_N";
> + };
> +
> + pin_gpio_z0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_RISER2_INT_N";
> + };
> +
> + pin_gpio_z2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_RISER2_RESET_N";
> + };
> +
> + pin_gpio_z3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "FM_BMC_PCH_SCI_LPC_N";
> + };
> +
> + pin_gpio_z4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_17";
> + };
> +
> + pin_gpio_z6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_20";
> + };
> +
> + pin_gpio_z7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_POST_CMPLT_N";
> + };
> +
> + pin_gpio_aa0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "HOST_BMC_USB_SEL";
> + };
> +
> + pin_gpio_aa1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_ALERT_N";
> + };
> +
> + pin_gpio_aa2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PVCCIN_CPU0_PWR_IN_ALERT_N";
> + };
> +
> + pin_gpio_aa3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PVCCIN_CPU1_PWR_IN_ALERT_N";
> + };
> +
> + pin_gpio_aa4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "USB_CABLE_DETECT_N";
> + };
> +
> + pin_gpio_aa5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_BUS1_RST_OUT_N";
> + };
> +
> + pin_gpio_aa6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_SMI_ACTIVE_N";
> + };
> +
> + pin_gpio_aa7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_BIOS_POST_CMPLT_N";
> + };
> +
> + pin_gpio_ab0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_TPM_MOD_PRES_N";
> + };
> +
> + pin_gpio_ab1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FORCE_NMI_SW_FPGA_N";
> + };
> +
> + pin_gpio_ab2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "1U_2U_PCBA_SEL_R";
> + };
> +
> + pin_gpio_ab3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "INTRUDED_PRES_N";
> + };
> +};
This is my last comment.
Thanks,
Patrick
> --
> 2.7.4
>
