Add fwnode support to the lm3630a driver and optionally allow
configuring the label, default brightness level, and maximum brightness
level. The two outputs can be controlled by bank A and B independently
or bank A can control both outputs.
If the platform data was not configured, then the driver defaults to
enabling both banks. This patch changes the default value to disable
both banks before parsing the firmware node so that just a single bank
can be enabled if desired. There are no in-tree users of this driver.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx>
Reviewed-by: Dan Murphy <dmurphy@xxxxxx>
---
Changes since v5
- None
Changes since v4
- Added new function lm3630a_parse_bank()
- Renamed seen variable to seen_led_sources
- Use the bitmask returned from lm3630a_parse_led_sources() to compare
against the seen_led_sources rather than just the control bank. This
eliminated another if statement that was previously present that
checked to see if control bank A should control both sinks.
- #define LM3630A_BANK_0, LM3630A_BANK_1, LM3630A_SINK_0,
LM3630A_SINK_1, and LM3630A_NUM_SINKS and use where appropriate.
- Changed all occurances of
'if (bank == 0) { BANK_A_WORK } else { BANK_B_WORK }' to
'if (bank) { BANK_B_WORK } else { BANK_A_WORK }'
- Dropped unnecessary 'ret = 0' from lm3630a_parse_led_sources().
- Changed 'if (ret < 0)' to 'if (ret)' in lm3630a_parse_node().
- Dropped kerneldoc from lm3630a_parse_led_sources().
Changes since v3
- Add support for label
- Changed lm3630a_parse_node() to return -ENODEV if no nodes were found
- Remove LM3630A_LED{A,B}_DISABLE
- Add two additional newlines for code readability
- Remove extra newline
Changes since v2
- Separated out control banks and outputs via the reg and led-sources
properties.
- Use fwnode instead of of API
- Disable both banks by default before calling lm3630a_parse_node()
- Add lots of error handling
- Check for duplicate source / bank definitions
- Remove extra ;
- Make probe() method fail if fwnode parsing fails.
drivers/video/backlight/lm3630a_bl.c | 149 ++++++++++++++++++++++-
include/linux/platform_data/lm3630a_bl.h | 4 +
2 files changed, 148 insertions(+), 5 deletions(-)
diff --git a/drivers/video/backlight/lm3630a_bl.c b/drivers/video/backlight/lm3630a_bl.c
index ef2553f452ca..75d996490cf0 100644
--- a/drivers/video/backlight/lm3630a_bl.c
+++ b/drivers/video/backlight/lm3630a_bl.c
@@ -35,6 +35,14 @@
#define REG_MAX 0x50
#define INT_DEBOUNCE_MSEC 10
+
+#define LM3630A_BANK_0 0
+#define LM3630A_BANK_1 1
+
+#define LM3630A_NUM_SINKS 2
+#define LM3630A_SINK_0 0
+#define LM3630A_SINK_1 1
+
struct lm3630a_chip {
struct device *dev;
struct delayed_work work;
@@ -329,15 +337,17 @@ static const struct backlight_ops lm3630a_bank_b_ops = {
static int lm3630a_backlight_register(struct lm3630a_chip *pchip)
{
- struct backlight_properties props;
struct lm3630a_platform_data *pdata = pchip->pdata;
+ struct backlight_properties props;
+ const char *label;
props.type = BACKLIGHT_RAW;
if (pdata->leda_ctrl != LM3630A_LEDA_DISABLE) {
props.brightness = pdata->leda_init_brt;
props.max_brightness = pdata->leda_max_brt;
+ label = pdata->leda_label ? pdata->leda_label : "lm3630a_leda";
pchip->bleda =
- devm_backlight_device_register(pchip->dev, "lm3630a_leda",
+ devm_backlight_device_register(pchip->dev, label,
pchip->dev, pchip,
&lm3630a_bank_a_ops, &props);
if (IS_ERR(pchip->bleda))
@@ -348,8 +358,9 @@ static int lm3630a_backlight_register(struct lm3630a_chip *pchip)
(pdata->ledb_ctrl != LM3630A_LEDB_ON_A)) {
props.brightness = pdata->ledb_init_brt;
props.max_brightness = pdata->ledb_max_brt;
+ label = pdata->ledb_label ? pdata->ledb_label : "lm3630a_ledb";
pchip->bledb =
- devm_backlight_device_register(pchip->dev, "lm3630a_ledb",
+ devm_backlight_device_register(pchip->dev, label,
pchip->dev, pchip,
&lm3630a_bank_b_ops, &props);
if (IS_ERR(pchip->bledb))
@@ -364,6 +375,123 @@ static const struct regmap_config lm3630a_regmap = {
.max_register = REG_MAX,
};
+static int lm3630a_parse_led_sources(struct fwnode_handle *node,
+ int default_led_sources)
+{
+ u32 sources[LM3630A_NUM_SINKS];
+ int ret, num_sources, i;
+
+ num_sources = fwnode_property_read_u32_array(node, "led-sources", NULL,
+ 0);
+ if (num_sources < 0)
+ return default_led_sources;
+ else if (num_sources > ARRAY_SIZE(sources))
+ return -EINVAL;
+
+ ret = fwnode_property_read_u32_array(node, "led-sources", sources,
+ num_sources);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < num_sources; i++) {
+ if (sources[i] < LM3630A_SINK_0 || sources[i] > LM3630A_SINK_1)
+ return -EINVAL;
+
+ ret |= BIT(sources[i]);
+ }
+
+ return ret;
+}
+
+static int lm3630a_parse_bank(struct lm3630a_platform_data *pdata,
+ struct fwnode_handle *node, int *seen_led_sources)
+{
+ int led_sources, ret;
+ const char *label;
+ u32 bank, val;
+ bool linear;
+
+ ret = fwnode_property_read_u32(node, "reg", &bank);
+ if (ret)
+ return ret;
+
+ if (bank < LM3630A_BANK_0 || bank > LM3630A_BANK_1)
+ return -EINVAL;
+
+ led_sources = lm3630a_parse_led_sources(node, BIT(bank));
+ if (led_sources < 0)
+ return led_sources;
+
+ if (*seen_led_sources & led_sources)
+ return -EINVAL;
+
+ *seen_led_sources |= led_sources;
+
+ linear = fwnode_property_read_bool(node,
+ "ti,linear-mapping-mode");
+ if (bank) {
+ if (led_sources & BIT(LM3630A_SINK_0) ||
+ !(led_sources & BIT(LM3630A_SINK_1)))
+ return -EINVAL;
+
+ pdata->ledb_ctrl = linear ?
+ LM3630A_LEDB_ENABLE_LINEAR :
+ LM3630A_LEDB_ENABLE;
+ } else {
+ if (!(led_sources & BIT(LM3630A_SINK_0)))
+ return -EINVAL;
+
+ pdata->leda_ctrl = linear ?
+ LM3630A_LEDA_ENABLE_LINEAR :
+ LM3630A_LEDA_ENABLE;
+
+ if (led_sources & BIT(LM3630A_SINK_1))
+ pdata->ledb_ctrl = LM3630A_LEDB_ON_A;
+ }
+
+ ret = fwnode_property_read_string(node, "label", &label);
+ if (!ret) {
+ if (bank)
+ pdata->ledb_label = label;
+ else
+ pdata->leda_label = label;
+ }
+
+ ret = fwnode_property_read_u32(node, "default-brightness",
+ &val);
+ if (!ret) {
+ if (bank)
+ pdata->ledb_init_brt = val;
+ else
+ pdata->leda_init_brt = val;
+ }
+
+ ret = fwnode_property_read_u32(node, "max-brightness", &val);
+ if (!ret) {
+ if (bank)
+ pdata->ledb_max_brt = val;
+ else
+ pdata->leda_max_brt = val;
+ }
+
+ return 0;
+}
+
+static int lm3630a_parse_node(struct lm3630a_chip *pchip,
+ struct lm3630a_platform_data *pdata)
+{
+ int ret = -ENODEV, seen_led_sources = 0;
+ struct fwnode_handle *node;
+
+ device_for_each_child_node(pchip->dev, node) {
+ ret = lm3630a_parse_bank(pdata, node, &seen_led_sources);
+ if (ret)
+ return ret;
+ }
+
+ return ret;
+}
+
static int lm3630a_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -396,13 +524,18 @@ static int lm3630a_probe(struct i2c_client *client,
GFP_KERNEL);
if (pdata == NULL)
return -ENOMEM;
+
/* default values */
- pdata->leda_ctrl = LM3630A_LEDA_ENABLE;
- pdata->ledb_ctrl = LM3630A_LEDB_ENABLE;
pdata->leda_max_brt = LM3630A_MAX_BRIGHTNESS;
pdata->ledb_max_brt = LM3630A_MAX_BRIGHTNESS;
pdata->leda_init_brt = LM3630A_MAX_BRIGHTNESS;
pdata->ledb_init_brt = LM3630A_MAX_BRIGHTNESS;
+
+ rval = lm3630a_parse_node(pchip, pdata);
+ if (rval) {
+ dev_err(&client->dev, "fail : parse node\n");
+ return rval;
+ }
}
pchip->pdata = pdata;
@@ -470,11 +603,17 @@ static const struct i2c_device_id lm3630a_id[] = {
{}
};
+static const struct of_device_id lm3630a_match_table[] = {
+ { .compatible = "ti,lm3630a", },
+ { },
+};
+
MODULE_DEVICE_TABLE(i2c, lm3630a_id);
static struct i2c_driver lm3630a_i2c_driver = {
.driver = {
.name = LM3630A_NAME,
+ .of_match_table = lm3630a_match_table,
},
.probe = lm3630a_probe,
.remove = lm3630a_remove,
diff --git a/include/linux/platform_data/lm3630a_bl.h b/include/linux/platform_data/lm3630a_bl.h
index 7538e38e270b..762e68956f31 100644
--- a/include/linux/platform_data/lm3630a_bl.h
+++ b/include/linux/platform_data/lm3630a_bl.h
@@ -38,9 +38,11 @@ enum lm3630a_ledb_ctrl {
#define LM3630A_MAX_BRIGHTNESS 255
/*
+ *@leda_label : optional led a label.
*@leda_init_brt : led a init brightness. 4~255
*@leda_max_brt : led a max brightness. 4~255
*@leda_ctrl : led a disable, enable linear, enable exponential
+ *@ledb_label : optional led b label.
*@ledb_init_brt : led b init brightness. 4~255
*@ledb_max_brt : led b max brightness. 4~255
*@ledb_ctrl : led b disable, enable linear, enable exponential
@@ -50,10 +52,12 @@ enum lm3630a_ledb_ctrl {
struct lm3630a_platform_data {
/* led a config. */
+ const char *leda_label;
int leda_init_brt;
int leda_max_brt;
enum lm3630a_leda_ctrl leda_ctrl;
/* led b config. */
+ const char *ledb_label;
int ledb_init_brt;
int ledb_max_brt;
enum lm3630a_ledb_ctrl ledb_ctrl;
--
2.20.1
