Re: [PATCH v2 1/5] dt-bindings: opp: Introduce bandwidth-MBps bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hey Viresh,

On 4/24/19 12:19 PM, Viresh Kumar wrote:
On 24-04-19, 12:16, Rajendra Nayak wrote:


On 4/23/2019 6:58 PM, Georgi Djakov wrote:
In addition to frequency and voltage, some devices may have bandwidth
requirements for their interconnect throughput - for example a CPU
or GPU may also need to increase or decrease their bandwidth to DDR
memory based on the current operating performance point.

Extend the OPP tables with additional property to describe the bandwidth
needs of a device. The average and peak bandwidth values depend on the
hardware and its properties.

Signed-off-by: Georgi Djakov <georgi.djakov@xxxxxxxxxx>
---
   Documentation/devicetree/bindings/opp/opp.txt | 38 +++++++++++++++++++
   .../devicetree/bindings/property-units.txt    |  4 ++
   2 files changed, 42 insertions(+)

diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt
index 76b6c79604a5..830f0206aea7 100644
--- a/Documentation/devicetree/bindings/opp/opp.txt
+++ b/Documentation/devicetree/bindings/opp/opp.txt
@@ -132,6 +132,9 @@ Optional properties:
   - opp-level: A value representing the performance level of the device,
     expressed as a 32-bit integer.
+- bandwidth-MBps: The interconnect bandwidth is specified with an array containing
+  the two integer values for average and peak bandwidth in megabytes per second.
+
   - clock-latency-ns: Specifies the maximum possible transition latency (in
     nanoseconds) for switching to this OPP from any other OPP.
@@ -546,3 +549,38 @@ Example 6: opp-microvolt-<name>, opp-microamp-<name>:
   		};
   	};
   };
+
+Example 7: bandwidth-MBps:
+Average and peak bandwidth values for the interconnects between CPU and DDR
+memory and also between CPU and L3 are defined per each OPP. Bandwidth of both
+interconnects is scaled together with CPU frequency.
+
+/ {
+	cpus {
+		CPU0: cpu@0 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			...
+			operating-points-v2 = <&cpu_opp_table>;
+			/* path between CPU and DDR memory and CPU and L3 */
+			interconnects = <&noc MASTER_CPU &noc SLAVE_DDR>,
+					<&noc MASTER_CPU &noc SLAVE_L3>;
+		};
+	};
+
+	cpu_opp_table: cpu_opp_table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			/* CPU<->DDR bandwidth: 457 MB/s average, 1525 MB/s peak */
+			 * CPU<->L3 bandwidth: 914 MB/s average, 3050 MB/s peak */
+			bandwidth-MBps = <457 1525>, <914 3050>;

Should this also have a bandwidth-MBps-name perhaps? Without that I guess we assume
the order in which we specify the interconnects is the same as the order here?

Right, so I suggested not to add the -name property and to rely on the
order. Though I missed that he hasn't mentioned the order thing here.

by skipping names, aren't we forced to specify all the specified paths
bandwidths for each opp even if it is redundant? i.e if the first/second
icc path doesn't have to change across a few opps but if the other path
does need to change this scheme would force it to be included and will
try to set the first/second path again.


e.g: Here the first path does not have to change across these two opps
but have to specified nonetheless since we omit names.

+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			bandwidth-MBps = <457 1525>, <914 3050>;
+		};
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			bandwidth-MBps = <457 1525>, <1828 6102>;
+		};



@Georgi: Please mention above in the binding that the order is same as
interconnects binding.


--
Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc, is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux