Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate Bus interface between a host system master and one or more slave interfaces. HyperBus is used to connect microprocessor, microcontroller, or ASIC devices with random access NOR flash memory (called HyperFlash) or self refresh DRAM (called HyperRAM). Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS) signal and either Single-ended clock(3.0V parts) or Differential clock (1.8V parts). It uses ChipSelect lines to select b/w multiple slaves. At bus level, it follows a separate protocol described in HyperBus specification[1]. HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar to that of existing parallel NORs. Since HyperBus is x8 DDR bus, its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But HyperBus operates at >166MHz frequencies. HyperRAM provides direct random read/write access to flash memory array. But, HyperBus memory controllers seem to abstract implementation details and expose a simple MMIO interface to access connected flash. Add support for registering HyperFlash devices with MTD framework. MTD maps framework along with CFI chip support framework are used to support communicating with flash. Framework is modelled along the lines of spi-nor framework. HyperBus memory controller (HBMC) drivers calls hyperbus_register_device() to register a single HyperFlash device. HyperFlash core parses MMIO access information from DT, sets up the map_info struct, probes CFI flash and registers it with MTD framework. Some HBMC masters need calibration/training sequence[3] to be carried out, in order for DLL inside the controller to lock, by reading a known string/pattern. This is done by repeatedly reading CFI Query Identification String. Calibration needs to be done before trying to detect flash as part of CFI flash probe. HyperRAM is not supported at the moment. HyperBus specification can be found at[1] HyperFlash datasheet can be found at[2] [1] https://www.cypress.com/file/213356/download [2] https://www.cypress.com/file/213346/download [3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf Table 12-5741. HyperFlash Access Sequence Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx> --- MAINTAINERS | 7 + drivers/mtd/Kconfig | 2 + drivers/mtd/Makefile | 1 + drivers/mtd/hyperbus/Kconfig | 11 ++ drivers/mtd/hyperbus/Makefile | 3 + drivers/mtd/hyperbus/hyperbus-core.c | 192 +++++++++++++++++++++++++++ include/linux/mtd/hyperbus.h | 91 +++++++++++++ 7 files changed, 307 insertions(+) create mode 100644 drivers/mtd/hyperbus/Kconfig create mode 100644 drivers/mtd/hyperbus/Makefile create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c create mode 100644 include/linux/mtd/hyperbus.h diff --git a/MAINTAINERS b/MAINTAINERS index d60b67e58ea8..7aa1b3454a89 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7243,6 +7243,13 @@ F: include/uapi/linux/hyperv.h F: tools/hv/ F: Documentation/ABI/stable/sysfs-bus-vmbus +HYPERBUS SUPPORT +M: Vignesh Raghavendra <vigneshr@xxxxxx> +S: Supported +F: drivers/mtd/hyperbus/ +F: include/linux/mtd/hyperbus.h +F: Documentation/devicetree/bindings/mtd/cypress,hyperbus.txt + HYPERVISOR VIRTUAL CONSOLE DRIVER L: linuxppc-dev@xxxxxxxxxxxxxxxx S: Odd Fixes diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig index aa5a27fdfdd1..03315fb9c895 100644 --- a/drivers/mtd/Kconfig +++ b/drivers/mtd/Kconfig @@ -289,4 +289,6 @@ source "drivers/mtd/spi-nor/Kconfig" source "drivers/mtd/ubi/Kconfig" +source "drivers/mtd/hyperbus/Kconfig" + endif # MTD diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile index 58fc327a5276..04c154906631 100644 --- a/drivers/mtd/Makefile +++ b/drivers/mtd/Makefile @@ -35,3 +35,4 @@ obj-y += chips/ lpddr/ maps/ devices/ nand/ tests/ obj-$(CONFIG_MTD_SPI_NOR) += spi-nor/ obj-$(CONFIG_MTD_UBI) += ubi/ +obj-$(CONFIG_MTD_HYPERBUS) += hyperbus/ diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig new file mode 100644 index 000000000000..98147e28caa0 --- /dev/null +++ b/drivers/mtd/hyperbus/Kconfig @@ -0,0 +1,11 @@ +menuconfig MTD_HYPERBUS + tristate "HyperBus support" + select MTD_CFI + select MTD_MAP_BANK_WIDTH_2 + select MTD_CFI_AMDSTD + select MTD_COMPLEX_MAPPINGS + help + This is the framework for the HyperBus which can be used by + the HyperBus Controller driver to communicate with + HyperFlash. See Cypress HyperBus specification for more + details diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile new file mode 100644 index 000000000000..ca61dedd730d --- /dev/null +++ b/drivers/mtd/hyperbus/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 + +obj-$(CONFIG_MTD_HYPERBUS) += hyperbus-core.o diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c new file mode 100644 index 000000000000..49aeb59742c6 --- /dev/null +++ b/drivers/mtd/hyperbus/hyperbus-core.c @@ -0,0 +1,192 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +// Author: Vignesh Raghavendra <vigneshr@xxxxxx> + +#include <linux/err.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mtd/hyperbus.h> +#include <linux/mtd/map.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/cfi.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/types.h> + +#define HYPERBUS_CALIB_COUNT 25 + +static struct hyperbus_device *map_to_hbdev(struct map_info *map) +{ + return container_of(map, struct hyperbus_device, map); +} + +static map_word hyperbus_read16(struct map_info *map, unsigned long addr) +{ + struct hyperbus_device *hbdev = map_to_hbdev(map); + struct hyperbus_ctlr *ctlr = hbdev->ctlr; + map_word read_data; + + read_data.x[0] = ctlr->ops->read16(hbdev, addr); + + return read_data; +} + +static void hyperbus_write16(struct map_info *map, map_word d, + unsigned long addr) +{ + struct hyperbus_device *hbdev = map_to_hbdev(map); + struct hyperbus_ctlr *ctlr = hbdev->ctlr; + + ctlr->ops->write16(hbdev, addr, d.x[0]); +} + +static void hyperbus_copy_from(struct map_info *map, void *to, + unsigned long from, ssize_t len) +{ + struct hyperbus_device *hbdev = map_to_hbdev(map); + struct hyperbus_ctlr *ctlr = hbdev->ctlr; + + ctlr->ops->copy_from(hbdev, to, from, len); +} + +static void hyperbus_copy_to(struct map_info *map, unsigned long to, + const void *from, ssize_t len) +{ + struct hyperbus_device *hbdev = map_to_hbdev(map); + struct hyperbus_ctlr *ctlr = hbdev->ctlr; + + ctlr->ops->copy_to(hbdev, to, from, len); +} + +/* Default calibration routine for use by HyperBus controller. + * Controller is calibrated by repeatedly reading known pattern ("QRY" + * string from CFI space) + * Lets ensure "QRY" string is read correctly at least 5 times to ensure + * stability of the DLL lock. + */ +int hyperbus_calibrate(struct hyperbus_device *hbdev) +{ + struct map_info *map = &hbdev->map; + struct cfi_private cfi; + int count = HYPERBUS_CALIB_COUNT; + int pass_count = 0; + int ret; + + cfi.interleave = 1; + cfi.device_type = CFI_DEVICETYPE_X16; + cfi_send_gen_cmd(0xF0, 0, 0, map, &cfi, cfi.device_type, NULL); + cfi_send_gen_cmd(0x98, 0x55, 0, map, &cfi, cfi.device_type, NULL); + + while (count--) { + cfi_qry_present(map, 0, &cfi); + ret = cfi_qry_present(map, 0, &cfi); + if (ret) + pass_count++; + else + pass_count = 0; + if (pass_count == 5) + break; + } + + cfi_qry_mode_off(0, map, &cfi); + + return ret; +} +EXPORT_SYMBOL_GPL(hyperbus_calibrate); + +int hyperbus_register_device(struct hyperbus_device *hbdev) +{ + const struct hyperbus_ops *ops; + struct hyperbus_ctlr *ctlr; + struct device_node *np; + struct map_info *map; + struct resource res; + struct device *dev; + int ret; + + if (!hbdev || !hbdev->np || !hbdev->ctlr || !hbdev->ctlr->dev) { + pr_err("hyperbus: please fill all the necessary fields!\n"); + return -EINVAL; + } + + np = hbdev->np; + ctlr = hbdev->ctlr; + if (!of_device_is_compatible(np, "cypress,hyperflash")) + return -ENODEV; + + hbdev->memtype = HYPERFLASH; + + if (of_address_to_resource(np, 0, &res)) + return -EINVAL; + + dev = ctlr->dev; + map = &hbdev->map; + map->size = resource_size(&res); + map->virt = devm_ioremap_resource(dev, &res); + if (IS_ERR(map->virt)) + return PTR_ERR(map->virt); + + map->name = dev_name(dev); + map->bankwidth = 2; + map->device_node = np; + + simple_map_init(map); + ops = ctlr->ops; + if (ops) { + if (ops->read16) + map->read = hyperbus_read16; + if (ops->write16) + map->write = hyperbus_write16; + if (ops->copy_to) + map->copy_to = hyperbus_copy_to; + if (ops->copy_from) + map->copy_from = hyperbus_copy_from; + + if (ops->calibrate && !ctlr->calibrated) { + ret = ops->calibrate(hbdev); + if (!ret) { + dev_err(dev, "Calibration failed\n"); + return -ENODEV; + } + ctlr->calibrated = true; + } + } + + hbdev->mtd = do_map_probe("cfi_probe", map); + if (!hbdev->mtd) { + dev_err(dev, "probing of hyperbus device failed\n"); + return -ENODEV; + } + + hbdev->mtd->dev.parent = dev; + mtd_set_of_node(hbdev->mtd, np); + + ret = mtd_device_register(hbdev->mtd, NULL, 0); + if (ret) { + dev_err(dev, "failed to register mtd device\n"); + map_destroy(hbdev->mtd); + return ret; + } + hbdev->registered = true; + + return 0; +} +EXPORT_SYMBOL_GPL(hyperbus_register_device); + +int hyperbus_unregister_device(struct hyperbus_device *hbdev) +{ + int ret = 0; + + if (hbdev && hbdev->mtd && hbdev->registered) { + ret = mtd_device_unregister(hbdev->mtd); + map_destroy(hbdev->mtd); + } + + return ret; +} +EXPORT_SYMBOL_GPL(hyperbus_unregister_device); + +MODULE_DESCRIPTION("HyperBus Framework"); +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@xxxxxx>"); diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h new file mode 100644 index 000000000000..19340cc56aa4 --- /dev/null +++ b/include/linux/mtd/hyperbus.h @@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 + * + * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ + */ + +#ifndef __LINUX_MTD_HYPERBUS_H__ +#define __LINUX_MTD_HYPERBUS_H__ + +#include <linux/mtd/map.h> + +enum hyperbus_memtype { + HYPERFLASH, + HYPERRAM, +}; + +/** + * struct hyperbus_device - struct representing HyperBus slave device + * @map: map_info struct for accessing MMIO HyperBus flash memory + * @np: pointer to HyperBus slave device node + * @mtd: pointer to MTD struct + * @ctlr: pointer to HyperBus controller struct + * @memtype: type of memory device: HyperFlash or HyperRAM + * @registered: flag to indicate whether device is registered with MTD core + */ + +struct hyperbus_device { + struct map_info map; + struct device_node *np; + struct mtd_info *mtd; + struct hyperbus_ctlr *ctlr; + enum hyperbus_memtype memtype; + bool registered; +}; + +/** + * struct hyperbus_ops - struct representing custom HyperBus operations + * @read16: read 16 bit of data, usually from register/ID-CFI space + * @write16: write 16 bit of data, usually to register/ID-CFI space + * @copy_from: copy data from flash memory + * @copy_to: copy data to flash memory + * @calibrate: calibrate HyperBus controller + */ + +struct hyperbus_ops { + u16 (*read16)(struct hyperbus_device *hbdev, unsigned long addr); + void (*write16)(struct hyperbus_device *hbdev, + unsigned long addr, u16 val); + void (*copy_from)(struct hyperbus_device *hbdev, void *to, + unsigned long from, ssize_t len); + void (*copy_to)(struct hyperbus_device *dev, unsigned long to, + const void *from, ssize_t len); + int (*calibrate)(struct hyperbus_device *dev); +}; + +/** + * struct hyperbus_ctlr - struct representing HyperBus controller + * @calibrated: flag to indicate ctlr calibration sequence is complete + * @ops: HyperBus controller ops + */ +struct hyperbus_ctlr { + struct device *dev; + bool calibrated; + + const struct hyperbus_ops *ops; +}; + +/** + * hyperbus_calibrate - default calibration routine for use by HyperBus ctlr. + * @hbdev: hyperbus_device to be used for calibration + * + * Return: 0 for success, others for failure. + */ +int hyperbus_calibrate(struct hyperbus_device *hbdev); + +/** + * hyperbus_register_device - probe and register a HyperBus slave memory device + * @hbdev: hyperbus_device struct with dev, np and ctlr field populated + * + * Return: 0 for success, others for failure. + */ +int hyperbus_register_device(struct hyperbus_device *hbdev); + +/** + * hb_unregister_device - deregister HyperBus slave memory device + * @hbdev: hyperbus_device to be unregistered + * + * Return: 0 for success, others for failure. + */ +int hyperbus_unregister_device(struct hyperbus_device *hbdev); + +#endif /* __LINUX_MTD_HYPERBUS_H__ */ -- 2.21.0
