Hi Jyri,
Thank you for the patch.
On Fri, Mar 22, 2019 at 10:06:14AM +0200, Jyri Sarha wrote:
> The sii902x chip family supports also HDMI audio. Add binding for
> describing the necessary i2s and mclk wiring for it.
>
> Signed-off-by: Jyri Sarha <jsarha@xxxxxx>
> ---
> .../bindings/display/bridge/sii902x.txt | 33 +++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> index c4c1855ca654..e78d069da439 100644
> --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
> @@ -9,6 +9,33 @@ Optional properties:
> about hotplug events.
> - reset-gpios: OF device-tree gpio specification for RST_N pin.
>
> + HDMI audio properties:
> + - sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3
> + Each integer indicates which i2s pin is connected to which
> + audio fifo. The first integer selects i2s audio pin for the
> + first audio fifo#0 (HDMI channels 1&2), second for fifo#1
> + (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
> + pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
> + but there can be no gaps. E.g. an i2s pin must be mapped to
> + fifo#0 and fifo#1 before mapping a channel to fifo#2.
> + I2S HDMI audio is configured only if this property is found.
> + - clocks: phandle and clock specifier for each clock listed in
> + the clock-names property
> + - clock-names: "mclk"
> + Describes SII902x MCLK input. MCLK is used to produce
> + HDMI audio CTS values. This property is required if
> + "i2s-data-lanes"-property is present. This property follows
> + Documentation/devicetree/bindings/clock/clock-bindings.txt
> + consumer binding.
> +
> + If HDMI audio is configured the sii902x device becomes an ASoC
> + codec component, that can be used in configuring full audio
> + devices with ASoC simple-card or audio-graph-card. See their
> + binding documents on how to describe how the sii902x device is
> + connected to the rest of the audio system:
> + Documentation/devicetree/bindings/sound/simple-card.txt
> + Documentation/devicetree/bindings/sound/audio-graph-card.txt
> +
> Optional subnodes:
> - video input: this subnode can contain a video input port node
> to connect the bridge to a display controller output (See this
> @@ -21,6 +48,12 @@ Example:
> compatible = "sil,sii9022";
> reg = <0x39>;
> reset-gpios = <&pioA 1 0>;
> +
> + #sound-dai-cells = <0>;
> + i2s-data-lanes = < 0 1 2 >;
This doesn't have the sil, prefix documented above. As stated in a
previous review, I wouldn't add a vendor prefix to this property as it
isn't vendor-specific, but I would then document it in a separate file
for common I2S properties.
Rob, what's your opinion ?
> + clocks = <&mclk>;
> + clock-names = "mclk";
> +
> ports {
> #address-cells = <1>;
> #size-cells = <0>;
--
Regards,
Laurent Pinchart
