Re: [PATCH 26/30] dt-bindings: pci: tegra: Document nvidia,plat-gpios optional prop

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 16-Apr-19 9:04 PM, Thierry Reding wrote:
> On Mon, Apr 15, 2019 at 11:28:29PM +0530, Manikanta Maddireddy wrote:
>>
>> On 15-Apr-19 7:46 PM, Thierry Reding wrote:
>>> On Thu, Apr 11, 2019 at 10:33:51PM +0530, Manikanta Maddireddy wrote:
>>>> Document "nvidia,plat-gpios" optional property which supports configuring
>>>> of platform specific gpios.
>>>>
>>>> Signed-off-by: Manikanta Maddireddy <mmaddireddy@xxxxxxxxxx>
>>>> ---
>>>>  Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt | 3 +++
>>>>  1 file changed, 3 insertions(+)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
>>>> index fbbd3bcb3435..dca8393b86d1 100644
>>>> --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
>>>> +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
>>>> @@ -73,6 +73,8 @@ Optional properties:
>>>>    pinctrl phandle to allow driver to explicitly put PCIe IO in DPD state.
>>>>  - pinctrl-1: PCIe IO(bias & REFCLK) deep power down(DPD) enable state.
>>>>    Pass pinctrl phandle to allow driver bring PCIe IO out of DPD state.
>>>> +- nvidia,plat-gpios: A list of platform specific gpios which controls
>>>> +  endpoint's internal regulator or PCIe logic.
>>> We discussed this with Vidya during review of the Tegra194 PCIe device
>>> tree bindings and arrived at the conclusion that all of the GPIOs that
>>> need to be controlled for PCI to work can be modelled as proper device
>>> nodes (I think regulator and GPIO-controlled muxes were the only two
>>> use-cases for which we need this).
>>>
>>> Can the same be done for this PCI controller? What use-cases are we
>>> talking about?
>> In Tegra194 case it is apt to use regulator framework because gpios are used
>> to control regulators. However I published this patch to control vendor defined
>> gpios in endpoints. For ex: isolate gpio in RTL8111. Since I am not sure if
>> regulator framework is apt, I published as gpio patch.
>>>>  Required properties on Tegra124 and later (deprecated):
>>>>  - phys: Must contain an entry for each entry in phy-names.
>>>> @@ -567,6 +569,7 @@ Board DTS:
>>>>  		pci@2,0 {
>>>>  			phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>;
>>>>  			phy-names = "pcie-0";
>>>> +			nvidia,plat-gpios = <&gpio TEGRA_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
>>>>  			status = "okay";
>>>>  		};
>>>>  	};
>>> I recall this being the setup for Jetson Nano and the X.3 GPIO going to
>>> an Ethernet device. Let's find out what exactly this GPIO is used for
>>> and why we need it to be set up as part of the PCI controller driver
>>> rather than the Ethernet device.
>>>
>>> If it turns out we can't model this other than with a generic GPIO type
>>> of property we need a better explanation than the above, and the Jetson
>>> Nano use-case would provide that explanation.
>>>
>>> And if indeed we cannot model this more accurately, I think we should
>>> use something like the gpio-hog binding rather than some custom PCI
>>> controller property.
>>>
>>> Thierry
>> Yes, in Jetson Nano gpio x.3 is controlling isolate pin of RTL8111.
>> RTL8111 datasheet available online says that as long as isolate
>> pin is asserted it'll not sample RX lanes and doesn't drive TX lanes.
>> Since RTL8111 PCIe IP should be active when PCIe host driver is
>> attempting link up, this gpio can be controlled by host driver only.
>>
>> I didn't go for gpio-hog because this gpio should be asserted
>> during suspend, to enable wake on LAN.
> I don't see code in gpiolib that would cause this to be deasserted
> during suspend.
>
> Is there ever a need to manipulate this GPIO at all? Or do we just
> need to make sure that it's always asserted?

Following steps
1) ISOLATEB gpio should be deasserted during boot to enable PCIe section
of RTL8111
2) PCIe host driver enumerates RTL8111
3) When suspend is initiated, ISOLATEB gpio should be asserted after PCIe
host controller suspend is completed to disable PCIe section of RTL8111
and enable Wake on LAN
4) During resume, first ISOLATE gpio should be deasserted to get PCIe link up

> The problem with adding this to nvidia,plat-gpios in the PCI root port
> node is that there's no context at all, so the PCI host driver can't
> really do anything with this, other than perhaps exactly one fixed
> operation, but then it's pretty much equivalent to a gpio-hog.
>
> If we do need control over the pin, I think it might be worth looking at
> adding support to gpiolib for initial pin configuration (so that it does
> not hog the GPIO, but still configures it). That would allow us to take
> the PCI device out of isolation initially and once the device has been
> probed we can control the GPIO from the PCI device. That way the device
> driver has the necessary context to assert and deassert the pin at the
> appropriate time, while still giving us the possibility to make the
> device appear on the PCI bus.

ISOLATEB gpio disables the PCIe section in RTL8111(Rx is not sampled &
doesn't drive Tx), if PCI client driver controls it, then it has
to do it after host controller suspend_noirq callback is completed.
Only suspend callback available after suspend_noirq is syscore_ops.
I didn't go with it because it is take void arguments, so client
driver has to maintain global pointers and I see only core drivers
like irqchip, clk, etc are using it.

Manikanta

>
> As a side-note, I think it would've been better if the ISOLATEB signal
> was wired up such that it would've been active by default. That would
> mean that if the bootloader and/or OS were not aware of the ISOLATEB
> signal, they would still be able to use the Ethernet device. I think
> that would've been a more sensible default, especially if the bus that
> the device is on requires the signal to be controlled without even
> knowing that the device exists.
>
> Thierry




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux