Some SPI Master controllers support configuring Least significant byte
first or Most significant byte first order for transfers. Also some SPI
slave devices expect bytes to be in Least significant first order and
some devices expect Most significant first order.
SPI driver declares mode and mode_bits as u16 and all bits are used.
This patch changes mode and mode_bits to be u32 to allow for more mode
configurations.
This patch also creates SPI_LSBYTE_FIRST mode to allow SPI clients to
choose LSByte order or MSByte order through the device tree property
spi-lsbyte-first.
Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
---
drivers/spi/spi.c | 5 ++++-
include/linux/spi/spi.h | 7 ++++---
2 files changed, 8 insertions(+), 4 deletions(-)
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index bd2a424672df..97ce047a776b 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -1638,6 +1638,8 @@ static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
spi->mode |= SPI_3WIRE;
if (of_property_read_bool(nc, "spi-lsb-first"))
spi->mode |= SPI_LSB_FIRST;
+ if (of_property_read_bool(nc, "spi-lsbyte-first"))
+ spi->mode |= SPI_LSBYTE_FIRST;
/*
* For descriptors associated with the device, polarity inversion is
@@ -2979,10 +2981,11 @@ int spi_setup(struct spi_device *spi)
spi_set_cs(spi, false);
- dev_dbg(&spi->dev, "setup mode %d, %s%s%s%s%u bits/w, %u Hz max --> %d\n",
+ dev_dbg(&spi->dev, "setup mode %d, %s%s%s%s%s%u bits/w, %u Hz max --> %d\n",
(int) (spi->mode & (SPI_CPOL | SPI_CPHA)),
(spi->mode & SPI_CS_HIGH) ? "cs_high, " : "",
(spi->mode & SPI_LSB_FIRST) ? "lsb, " : "",
+ (spi->mode & SPI_LSBYTE_FIRST) ? "lsbyte, " : "",
(spi->mode & SPI_3WIRE) ? "3wire, " : "",
(spi->mode & SPI_LOOP) ? "loopback, " : "",
spi->bits_per_word, spi->max_speed_hz,
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index a0975cf76cf6..d5c86b763f43 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -143,7 +143,7 @@ struct spi_device {
u32 max_speed_hz;
u8 chip_select;
u8 bits_per_word;
- u16 mode;
+ u32 mode;
#define SPI_CPHA 0x01 /* clock phase */
#define SPI_CPOL 0x02 /* clock polarity */
#define SPI_MODE_0 (0|0) /* (original MicroWire) */
@@ -164,6 +164,7 @@ struct spi_device {
#define SPI_TX_OCTAL 0x2000 /* transmit with 8 wires */
#define SPI_RX_OCTAL 0x4000 /* receive with 8 wires */
#define SPI_3WIRE_HIZ 0x8000 /* high impedance turnaround */
+#define SPI_LSBYTE_FIRST 0x10000 /* per-word bytes-on-wire */
int irq;
void *controller_state;
void *controller_data;
@@ -439,7 +440,7 @@ struct spi_controller {
u16 dma_alignment;
/* spi_device.mode flags understood by this controller driver */
- u16 mode_bits;
+ u32 mode_bits;
/* bitmask of supported bits_per_word for transfers */
u32 bits_per_word_mask;
@@ -1276,7 +1277,7 @@ struct spi_board_info {
/* mode becomes spi_device.mode, and is essential for chips
* where the default of SPI_CS_HIGH = 0 is wrong.
*/
- u16 mode;
+ u32 mode;
/* ... may need additional spi_device chip config data here.
* avoid stuff protocol drivers can set; but include stuff
--
2.7.4
