From: Mathieu Malaterre <malat@xxxxxxxxxx>
[ Upstream commit 3e3380d0675d5e20b0af067d60cb947a4348bf9b ]
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@xxxxxxxxxxxxxxxxxx>
Suggested-by: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Mathieu Malaterre <malat@xxxxxxxxxx>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@xxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
arch/arm/boot/dts/lpc32xx.dtsi | 18 +++++++++---------
1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi
index b7303a4e4236..ed0d6fb20122 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/lpc32xx.dtsi
@@ -230,7 +230,7 @@
status = "disabled";
};
- i2s1: i2s@2009C000 {
+ i2s1: i2s@2009c000 {
compatible = "nxp,lpc3220-i2s";
reg = <0x2009C000 0x1000>;
};
@@ -273,7 +273,7 @@
status = "disabled";
};
- i2c1: i2c@400A0000 {
+ i2c1: i2c@400a0000 {
compatible = "nxp,pnx-i2c";
reg = <0x400A0000 0x100>;
interrupt-parent = <&sic1>;
@@ -284,7 +284,7 @@
clocks = <&clk LPC32XX_CLK_I2C1>;
};
- i2c2: i2c@400A8000 {
+ i2c2: i2c@400a8000 {
compatible = "nxp,pnx-i2c";
reg = <0x400A8000 0x100>;
interrupt-parent = <&sic1>;
@@ -295,7 +295,7 @@
clocks = <&clk LPC32XX_CLK_I2C2>;
};
- mpwm: mpwm@400E8000 {
+ mpwm: mpwm@400e8000 {
compatible = "nxp,lpc3220-motor-pwm";
reg = <0x400E8000 0x78>;
status = "disabled";
@@ -394,7 +394,7 @@
#gpio-cells = <3>; /* bank, pin, flags */
};
- timer4: timer@4002C000 {
+ timer4: timer@4002c000 {
compatible = "nxp,lpc3220-timer";
reg = <0x4002C000 0x1000>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
@@ -412,7 +412,7 @@
status = "disabled";
};
- watchdog: watchdog@4003C000 {
+ watchdog: watchdog@4003c000 {
compatible = "nxp,pnx4008-wdt";
reg = <0x4003C000 0x1000>;
clocks = <&clk LPC32XX_CLK_WDOG>;
@@ -451,7 +451,7 @@
status = "disabled";
};
- timer1: timer@4004C000 {
+ timer1: timer@4004c000 {
compatible = "nxp,lpc3220-timer";
reg = <0x4004C000 0x1000>;
interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
@@ -475,7 +475,7 @@
status = "disabled";
};
- pwm1: pwm@4005C000 {
+ pwm1: pwm@4005c000 {
compatible = "nxp,lpc3220-pwm";
reg = <0x4005C000 0x4>;
clocks = <&clk LPC32XX_CLK_PWM1>;
@@ -484,7 +484,7 @@
status = "disabled";
};
- pwm2: pwm@4005C004 {
+ pwm2: pwm@4005c004 {
compatible = "nxp,lpc3220-pwm";
reg = <0x4005C004 0x4>;
clocks = <&clk LPC32XX_CLK_PWM2>;
--
2.19.1
