On 3/21/19 9:10 AM, Bartosz Golaszewski wrote:
From: David Lechner <david@xxxxxxxxxxxxxx>
This adds a cpu node and operating points to the common da850.dtsi file.
Additionally, a regulator is added to the LEGO EV3 board along with
some board-specific CPU configuration.
Should mention the LCDK board here as well since it is included in this
patch.
Regulators need to be hooked up on other boards to get them working.
Signed-off-by: David Lechner <david@xxxxxxxxxxxxxx>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
---
arch/arm/boot/dts/da850-lcdk.dts | 31 +++++++++++++++
arch/arm/boot/dts/da850-lego-ev3.dts | 30 +++++++++++++++
arch/arm/boot/dts/da850.dtsi | 56 ++++++++++++++++++++++++++++
3 files changed, 117 insertions(+)
diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/da850-lcdk.dts
index 26f453dc8370..f29ed9010812 100644
--- a/arch/arm/boot/dts/da850-lcdk.dts
+++ b/arch/arm/boot/dts/da850-lcdk.dts
@@ -155,12 +155,43 @@
};
};
};
+
+ cvdd: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cvdd";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&ref_clk {
clock-frequency = <24000000>;
};
+&cpu {
+ cpu-supply = <&cvdd>;
+};
+
+/* LCDK has a fixed CVDD of 1.3V, so only op points >= 300MHz are valid */
+
+&opp_100 {
+ status = "disabled";
+};
+
+&opp_200 {
+ status = "disabled";
+};
+
+&opp_375 {
+ status = "okay";
+};
+
+&opp_456 {
+ status = "okay";
+};
+
&pmx_core {
status = "okay";
diff --git a/arch/arm/boot/dts/da850-lego-ev3.dts b/arch/arm/boot/dts/da850-lego-ev3.dts
index 66fcadf0ba91..553717f84483 100644
--- a/arch/arm/boot/dts/da850-lego-ev3.dts
+++ b/arch/arm/boot/dts/da850-lego-ev3.dts
@@ -125,6 +125,15 @@
amp-supply = <&>;
};
+ cvdd: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cvdd";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
/*
* This is a 5V current limiting regulator that is shared by USB,
* the sensor (input) ports, the motor (output) ports and the A/DC.
@@ -204,6 +213,27 @@
clock-frequency = <24000000>;
};
+&cpu {
+ cpu-supply = <&cvdd>;
+};
+
+/* since we have a fixed regulator, we can't run at these points */
+&opp_100 {
+ status = "disabled";
+};
+
+&opp_200 {
+ status = "disabled";
+};
+
+/*
+ * The SoC is actually the 456MHz version, but because of the fixed regulator
+ * This is the fastest we can go.
+ */
+&opp_375 {
+ status = "okay";
+};
+
&pmx_core {
status = "okay";
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 559659b399d0..ee61d1253b58 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -20,6 +20,62 @@
reg = <0xc0000000 0x0>;
};
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu: cpu@0 {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&psc0 14>;
+ operating-points-v2 = <&opp_table>;
+ };
+ };
+
+ opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp_100: opp100-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ opp-microvolt = <1000000 950000 1050000>;
+ };
+
+ opp_200: opp110-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ opp-microvolt = <1100000 1050000 1160000>;
+ };
+
+ opp_300: opp120-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ opp-microvolt = <1200000 1140000 1320000>;
+ };
+
+ /*
+ * Original silicon was 300MHz max, so higher frequencies
+ * need to be enabled on a per-board basis if the chip is
+ * capable.
+ */
+
+ opp_375: opp120-375000000 {
+ status = "disabled";
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <1200000 1140000 1320000>;
+ };
+
+ opp_415: opp130-415000000 {
+ status = "disabled";
+ opp-hz = /bits/ 64 <415000000>;
+ opp-microvolt = <1300000 1250000 1350000>;
+ };
I just made this point (415MHz) up for experimenting with undervolting
before going all the way to 456MHz at 1.2V. I'm not sure if it is
actually useful to anyone else.
+
+ opp_456: opp130-456000000 {
+ status = "disabled";
+ opp-hz = /bits/ 64 <456000000>;
+ opp-microvolt = <1300000 1250000 1350000>;
+ };
+ };
+
arm {
#address-cells = <1>;
#size-cells = <1>;
