[PATCH v6 02/13] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes more
sense to use the more generic ECC term.

Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
---

Notes:
    v3: New patch
    
    v4: No change
    
    v5: No change
    
    v6: No change

 .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
index a5b940f18bf6..5a45cc54f46d 100644
--- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
@@ -1,4 +1,4 @@
-* Ingenic JZ4780 NAND/BCH
+* Ingenic JZ4780 NAND/ECC
 
 This file documents the device tree bindings for NAND flash devices on the
 JZ4780. NAND devices are connected to the NEMC controller (described in
@@ -14,10 +14,10 @@ Required NAND controller device properties:
   an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
 
 Optional NAND controller device properties:
-- ingenic,bch-controller: To make use of the hardware BCH controller, this
-  property must contain a phandle for the BCH controller node. The required
+- ingenic,bch-controller: To make use of the hardware ECC controller, this
+  property must contain a phandle for the ECC controller node. The required
   properties for this node are described below. If this is not specified,
-  software BCH will be used instead.
+  software ECC will be used instead.
 
 Optional children nodes:
 - Individual NAND chips are children of the NAND controller node.
@@ -70,17 +70,17 @@ nemc: nemc@13410000 {
 	};
 };
 
-The BCH controller is a separate SoC component used for error correction on
+The ECC controller is a separate SoC component used for error correction on
 NAND devices. The following is a description of the device properties for a
-BCH controller.
+ECC controller.
 
-Required BCH properties:
+Required ECC properties:
 - compatible: Should be one of:
   * ingenic,jz4740-ecc
   * ingenic,jz4725b-bch
   * ingenic,jz4780-bch
-- reg: Should specify the BCH controller registers location and length.
-- clocks: Clock for the BCH controller.
+- reg: Should specify the ECC controller registers location and length.
+- clocks: Clock for the ECC controller.
 
 Example:
 
-- 
2.11.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux