On Fri, Mar 15, 2019 at 06:38:25PM +0530, Jagan Teki wrote:
> This patch add support for Bananapi S070WV20-CT16 DSI panel to
> BPI-M64 board.
>
> Bananapi S070WV20-CT16 is a pure RGB output panel with ICN6211 DSI/RGB
> convertor bridge, so enable bridge along with associated panel.
>
> DSI panel connected via board DSI port with,
> - DLDO1 as VCC-DSI supply
> - PD6 gpio for reset pin
> - PD5 gpio for backlight enable pin
> - PD7 gpio for backlight vdd supply
>
> Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> ---
> .../dts/allwinner/sun50i-a64-bananapi-m64.dts | 63 +++++++++++++++++++
> 1 file changed, 63 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
> index 7793ebb5d2b8..f31083aa4521 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
> @@ -45,6 +45,7 @@
> #include "sun50i-a64.dtsi"
>
> #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pwm/pwm.h>
>
> / {
> model = "BananaPi-M64";
> @@ -56,6 +57,15 @@
> serial1 = &uart1;
> };
>
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
> + brightness-levels = <1 2 4 8 16 32 64 128 512>;
> + default-brightness-level = <2>;
> + enable-gpios = <&pio 3 5 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PD5 */
> + power-supply = <®_vdd_backlight>;
> + };
> +
> chosen {
> stdout-path = "serial0:115200n8";
> };
> @@ -91,6 +101,26 @@
> };
> };
>
> + panel-connector {
> + compatible = "bananapi,s070wv20-ct16", "simple-panel";
> +
> + port {
> + backlight = <&backlight>;
> + panel_ep: endpoint {
> + remote-endpoint = <&bridge_out_ep>;
> + };
> + };
> + };
> +
> + reg_vdd_backlight: vdd-backlight {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-backlight";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 3 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PD7 */
> + enable-active-high;
> + };
> +
> wifi_pwrseq: wifi_pwrseq {
> compatible = "mmc-pwrseq-simple";
> reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> @@ -116,6 +146,33 @@
> status = "okay";
> };
>
> +&dphy {
> + status = "okay";
> +};
> +
> +&dsi {
> + vcc-dsi-supply = <®_dldo1>; /* VCC3V3-DSI */
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bridge@0 {
> + compatible = "bananapi,icn6211", "chipone, icn6211";
There's a typo in the compatible
> + reg = <0>;
> + reset-gpios = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD6 */
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <1>;
> +
> + bridge_out_ep: endpoint {
> + remote-endpoint = <&panel_ep>;
> + };
> + };
The port here should be under a node called ports, with two ports,
which is what you documented in your binding.
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Attachment:
signature.asc
Description: PGP signature
