On Mon, Mar 11, 2019 at 8:47 PM Angus Ainslie (Purism) <angus@xxxxxxxx> wrote:
> +/ {
> + model = "Purism Librem 5 devkit 1.0";
> + compatible = "fsl,librem5-devkit", "fsl,imx8mq";
This board is not manufactured by FSL/NXP, so it should be
"purism,librem5-devkit", "fsl,imx8mq" instead.
You should also add an entry for the purism vendor entry in
Documentation/devicetree/bindings/vendor-prefixes.txt in a separate
patch.
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + reg_usdhc2_vmmc: regulator-vsd-3v3 {
The usual format would be:
reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
Always on? It would be better to pass this regulator inside the mmc node.
> + };
> +
> + reg_pwr_en: pwr_en {
reg_pwr_en: regulator-pwr-en {
> + compatible = "regulator-fixed";
> + regulator-name = "PWR_EN";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
Same here. No need for "regulator-always-on" as it is controlled by
the gyroscope.
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + fsl,magic-packet;
> + status = "okay";
> + phy-supply = <®_pwr_en>;
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
You pass @0 and use reg = <1>, which is a mismatch. Building it with
W=1 would have warned you about this mismatch.
> + at803x,led-act-blind-workaround;
> + at803x,eee-disabled;
> + power-supply = <®_pwr_en>;
> + };
> + };
> +};
> +
> +&iomuxc {
> + imx8m-som {
No need for this imx8m-som level.
> + pinctrl_nc: ncgrp {
Not a very descriptive naming.
> + fsl,pins = <
> + MX8MQ_IOMUXC_SAI1_MCLK_SAI1_MCLK 0x00
> + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f
> + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f
> + >;
> + };
> +
> + pinctrl_up: upgrp {
Same here. Also, this is not used. Please remove it.
> + fsl,pins = <
> + MX8MQ_IOMUXC_SAI1_TXD2_SAI1_TX_DATA2 0x00
> + >;
> + };
> +
> + pinctrl_csi1: csi1grp {
This is not used at the moment. Please remove it and re-add it when
CSI gets supported.
> + fsl,pins = <
> + /* CSI_nRST */
> + MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x11
> + /* CSI_PWDN */
> + MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
> + /* CLK01 */
> + MX8MQ_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x19
> + >;
> + };
> +
> + pinctrl_pwr_en: pwr_engrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x06
> + >;
> + };
> +
> + pinctrl_wwan: wwan_grp {
Not used. Please remove this one and all unused pinctrl nodes.
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic: bd71837@4b {
Node names should be generic: pmic@4b
> + typec_ptn5100: ptn5110@52 {
Same here.
> + charger: charger@6b { /* bq25896 */
> + compatible = "ti,bq25890";
> + reg = <0x6b>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_charger>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + ti,battery-regulation-voltage = <4192000>; // 4.192V
> + ti,charge-current = <1600000>; // 1.6 A
> + ti,termination-current = <66000>; // 66mA
> + ti,precharge-current = <1300000>; // 1.3A
> + ti,minimum-sys-voltage = <2750000>; // 2.75V
> + ti,boost-voltage = <5000000>; // 5V
> + ti,boost-max-current = <50000>; // 50mA
No // style comments, please/
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>, <&pinctrl_imu>;
> + status = "okay";
> +
> + lsm9d: lsm9d@6a {
> + compatible = "st,lsm9ds1-gyro";
I don't find this binding.
> + reg = <0x6a>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> + power-supply = <®_pwr_en>;
> + };
> +};
> +&uart4 { /* BT */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_bt>;
> + fsl,uart-has-rtscts;
uart-has-rtscts is preferred.
> + /* resets = <&modem_reset>; */
Please remove this line instead of commenting it out.
